> Weldments > Weld Beads > Fillet Weld Beads
Introduction
Administration
User Interface
SolidWorks Fundamentals
Moving from 2D to 3D
Assemblies
CircuitWorks
Configurations
Design Checker
Design Studies in SolidWorks
Drawings and Detailing
DFMXpress
DriveWorksXpress
FloXpress
Import and Export
Large Scale Design
Model Display
Mold Design
Motion Studies
Parts and Features
Routing
Sheet Metal
Simulation
SimulationXpress
Sketching
Sustainability Products
SolidWorks Utilities
Tolerancing
Toolbox
Weldments
Weldments Overview
Groups
Profiles and Cut Lists
Cut Lists
Adding Structural Members
Adding Groups
Weldments Toolbar
Weldment Feature
Weldments - Default Configurations
Structural Members
Creating a Custom Profile
Pierce Points
Trim and Extend
Gussets
End Caps
Weld Beads
Creating Weld Beads
Smart Weld Selection Tool
Changing the Type and Size of Weld Beads
Weld Bead PropertyManager
Weld Bead Properties Dialog Box
Fillet Weld Beads
Creating Sub Weldments
Custom Properties in Weldments
Weldment Cut Lists
Weldment Drawings
Workgroup PDM
Troubleshooting
Glossary
Hide Table of Contents Show Table of Contents

Weldments - Fillet Weld Beads

For performance purposes and additional enhancements, it is recommended that you use the Weld Bead tool instead of Fillet Bead to insert weld beads.

You can add full length, intermittent, or staggered fillet weld beads between any intersecting weldment entities such as structural members, plate weldments, or gussets.

To add fillet weld beads:

  1. Click Fillet Bead (Weldments toolbar) or Insert, Weldments, Fillet Bead.

  1. In the PropertyManager, set the following options, then click .

Arrow Side

Bead type:

Full length

 

Intermittent

 

Staggered

Arrow Side

Other Side

Fillet size . Length of the leg of the fillet bead.

Bead length (for Intermittent or Staggered). Length of each bead segment.

Pitch (for Intermittent or Staggered). Distance between the start of each bead.

When you insert a bead across a gap:

 

  • Full penetration. Applies the bead to the full depth .

  • Partial penetration. Applies the bead to the depth you enter in Penetration .

Tangent propagation:

Selected

Cleared

Face Set1 . Select one or more planar faces.

Face Set2 . Select one or more planar faces that intersect the first face set.

Intersecting Edges. Highlights edges where Face Set1 and Face Set2 intersect. You can right-click an edge and select Delete to remove it from the weld bead.

Other Side

Select Other Side to apply optional settings for Full Length and Intermittent types. If you selected Staggered as the Bead type, the Other Side is already displayed. Make selections as described for Arrow Side.

Related Topics

Weldments Overview

 



Related SolidWorks Forum Content

Provide feedback on this topic

SolidWorks welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Weldments - Fillet Weld Beads
*Comment:  
x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: SolidWorks 2011 SP05

The search functionality within the web help is in a beta test phase and you may experience periodic delays or interruptions in its performance. These are the normal and ordinary features of a beta test and shall not under any circumstances give rise to any liability on the part of DS SolidWorks or its licensors. The topics within the Web-based help are not beta topics; they document SolidWorks 2011 SP05.

To disable Web help from within SolidWorks and use local help instead, click Help > Use SolidWorks Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.