> Motion Studies > Motion Study Plots > Displacement, Velocity, and Acceleration Type Plots > Selecting Alternate Coordinate Systems for Result X, Y, or Z Component Values
Introduction
Administration
User Interface
SolidWorks Fundamentals
Moving from 2D to 3D
Assemblies
CircuitWorks
Configurations
SolidWorks Costing
Design Checker
Design Studies in SolidWorks
Drawings and Detailing
DFMXpress
DriveWorksXpress
FloXpress
Import and Export
Large Scale Design
Model Display
Mold Design
Motion Studies
Introduction to Motion Studies
Accessing and Naming Motion Studies
MotionManager Interface
Motion Elements
Motor and Force Profiles
General Techniques
Animation
Component Contact
Motion Study Plots
Displacement, Velocity, and Acceleration Type Plots
Tracing the Motion of a Point in an Assembly
Plotting the Part Center of Mass Position in an Assembly
Plotting the Linear Displacement, Velocity, or Acceleration of a Part
Plotting the Angular Displacement, Velocity, or Acceleration of a Part
Selecting Alternate Coordinate Systems for Result X, Y, or Z Component Values
Force and Torque Plots
Energy and Momentum Type Plots
Orientation, Reflected Load, and Other Plots
Including Motion Results in Sensors
Results PropertyManager (Motion Analysis only)
Plot Properties
Motion Study Mates
Motion Along a Path
Event-based Motion Analysis
Rigid Groups
Stress Analysis for Motion
Motion Study Troubleshooting
Parts and Features
Routing
Sheet Metal
Simulation
SimulationXpress
Sketching
Sustainability Products
SolidWorks Utilities
Tolerancing
Toolbox
Weldments
Workgroup PDM
Troubleshooting
Glossary
Hide Table of Contents Show Table of Contents

Selecting Alternate Coordinate Systems for Result X, Y, or Z Component Values

By default, when you specify the result resolved values as X Component, Y Component, or Z Component, the ground coordinate system defines the component directions. You can select a component in the assembly to define an alternate coordinate system.

To select an alternate coordinate system for a result plot of values in a component direction:

  1. From a Motion Analysis study, click Results and Plots (MotionManager toolbar).
  2. Select a category and subcategory for the result.

    For example, to define a result from the displacement of a part, select the Displacement/Velocity/Acceleration category and the Center of Mass Position subcategory.

  3. For Select result component, select the result resolved value direction:
    • X Component for resolved values in the X direction.
    • Y Component for resolved values in the Y direction.
    • Z Component for resolved values in the Z direction.

    For example, selecting X Component with the Displacement/Velocity/Acceleration category and the Center of Mass Position subcategory defines the result from the X component of displacement.

  4. Select the result features required for the result category and subcategory.

    For example, you can select a part face to define result from the X component of the displacement of the part.

  5. Select the part that defines the alternate coordinate system.

    The coordinate system of the selected part appears.

    Select this part only to select coordinates other than ground.

  6. Select the Plot Results options you require, and click .

    The result appears in the MotionManager tree.



Related SolidWorks Forum Content

Provide feedback on this topic

SolidWorks welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Selecting Alternate Coordinate Systems for Result X, Y, or Z Component Values
*Comment:  
x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: SolidWorks 2012 SP05

The search functionality within the web help is in a beta test phase and you may experience periodic delays or interruptions in its performance. These are the normal and ordinary features of a beta test and shall not under any circumstances give rise to any liability on the part of DS SolidWorks or its licensors. The topics within the Web-based help are not beta topics; they document SolidWorks 2012 SP05.

To disable Web help from within SolidWorks and use local help instead, click Help > Use SolidWorks Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.