Introduction
Administration
User Interface
SolidWorks Fundamentals
Moving from 2D to 3D
Assemblies
CircuitWorks
Configurations
Configurations Overview
ConfigurationManager
Configuration Previews
Manual Configurations
Creating and Editing Configurations Manually
Derived Configurations
Activating a Configuration
Configurable Items for Parts
Configurable Items for Assemblies
Special Assembly Configurations
SpeedPak
Component Configurations in an Assembly
Deleting a Configuration
Design Table Configurations
Modify Configurations
Specifying Configuration Parameters
Configuration Publisher
SolidWorks Costing
Design Checker
Design Studies in SolidWorks
Drawings and Detailing
DFMXpress
DriveWorksXpress
FloXpress
Import and Export
Large Scale Design
Model Display
Mold Design
Motion Studies
Parts and Features
Routing
Sheet Metal
Simulation
SimulationXpress
Sketching
Sustainability Products
SolidWorks Utilities
Tolerancing
Toolbox
Weldments
Workgroup PDM
Troubleshooting
Glossary
Hide Table of Contents Show Table of Contents

SpeedPak

SpeedPak creates a simplified configuration of an assembly without losing references. If you work with very large and complex assemblies, using a SpeedPak configuration can significantly improve performance while working in the assembly and its drawing.

Improvements in assembly performance are most noticeable in very large and complex assemblies.

A SpeedPak configuration is essentially a subset of the parts and faces of an assembly. Unlike regular configurations, where you can simplify an assembly only by suppressing components, SpeedPak simplifies without suppressing. Therefore, you can substitute a SpeedPak configuration for the full assembly in higher level assemblies without losing references. Because only a subset of the parts and faces is used, memory usage is reduced, which can increase performance of many operations.

When you make changes to an assembly, such as adding, deleting, or moving components, the changes are not automatically incorporated into the SpeedPak configuration, even when you rebuild the assembly. You must manually update the SpeedPak configuration to incorporate the changes.

When to Use SpeedPak

Use SpeedPak when you want to insert a complex large assembly into a higher level assembly, especially if you want to see the entire SpeedPak assembly, but need to mate and dimension only to relatively few locations.

You can also use SpeedPak to facilitate file sharing. The SpeedPak information is saved entirely within the assembly file. Therefore, when sharing an assembly, you can send just the assembly file. You do not need to include component files.

For example, suppose you design an engine assembly, and need to send it to your customer's design team so they can insert it in their vehicle design.
  1. You create a SpeedPak configuration of the engine assembly, including all the faces and bodies your customer plans to reference in their vehicle model.
  2. You send them just the engine assembly file. You do not need to send files for any of the engine component parts.
  3. They insert your engine assembly file into their vehicle assembly file. They can add mates and dimensions to all faces and bodies you included in the SpeedPak definition.

SpeedPak in Drawings

When you dimension SpeedPak configurations in drawings, you can only dimension to edges included in the SpeedPak, which are shown in black. Edges not included in the SpeedPak are shown in gray. When you print the drawing, all the lines print in black, unless you select Color / Gray scale in the Page Setup dialog box.

In a drawing document, when you create a bill of materials for an assembly whose active configuration is a SpeedPak configuration, you can include columns for other configurations in addition to the SpeedPak configuration.
In an assembly document, when you create a bill of materials for an assembly whose active configuration is a SpeedPak configuration, you can include only the active SpeedPak configuration in the BOM.

You can use Balloon (Annotations toolbar) to add balloons to all items in a SpeedPak assembly, but the Auto Balloon command is not supported.



Related SolidWorks Forum Content

Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   SpeedPak
*Comment:  
x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: SOLIDWORKS 2012 SP05

The search functionality within the web help is in a beta test phase and you may experience periodic delays or interruptions in its performance. These are the normal and ordinary features of a beta test and shall not under any circumstances give rise to any liability on the part of Dassault Systèmes SolidWorks Corporation or its licensors. The topics within the Web-based help are not beta topics; they document SOLIDWORKS 2012 SP05.

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.