Hide Table of Contents
CreateBsplineSurface Method (IModeler)

Creates a b-spline surface.

.NET Syntax

Visual Basic (Declaration) 
Function CreateBsplineSurface( _
   ByVal Props As System.Object, _
   ByVal UKnots As System.Object, _
   ByVal VKnots As System.Object, _
   ByVal CtrlPtCoords As System.Object _
) As System.Object
Visual Basic (Usage) 
Dim instance As IModeler
Dim Props As System.Object
Dim UKnots As System.Object
Dim VKnots As System.Object
Dim CtrlPtCoords As System.Object
Dim value As System.Object
 
value = instance.CreateBsplineSurface(Props, UKnots, VKnots, CtrlPtCoords)
C# 
System.object CreateBsplineSurface( 
   System.object Props,
   System.object UKnots,
   System.object VKnots,
   System.object CtrlPtCoords
)
C++/CLI 
System.Object^ CreateBsplineSurface( 
&   System.Object^ Props,
&   System.Object^ UKnots,
&   System.Object^ VKnots,
&   System.Object^ CtrlPtCoords
) 

Parameters

Props
Array containing 8 integers packed as 4 double elements (see Remarks)
UKnots
Array of numUKnots (see Remarks)
VKnots
Array of numVKnots (see Remarks)
CtrlPtCoords
rray of numCtrlPtCoord (see Remarks)

Return Value

B-spline surface

Remarks

The Props array contains the following elements. These are integers packed into a double array in the Dispatch version.

  • Uorder, Vorder

  • numV_CtrlPoints, numU_CtrlPoints

  • Uperiodicity, Vperiodicity

  • DimensionControlPoints, UNUSED ( set =0 )

 

Number of elements in this array...

Given by...

UKnots

numUKnots = numU_CtrlPoints + Uorder

VKnots

numVKnots = numV_CtrlPoints + Vorder

CtrlPtCoords

numCtrlPtCoord =( NumV_CtrlPoints * NumU_CtrlPoints * DimensionControlPoints )

NOTE: The order of the UV control points are reversed if you used ISurface::GetBSurfParams3 or ISurface::IGetBSurfParams to get the data. You do not need to reverse the UV control points; instead, you can switch the UV knots and related parameters.

For periodics, the first knot must have multiplicity = 1 and all excess multiplicity must be imposed on the last knot. Therefore, a valid periodic knot vector would be { 0, 1, 2, 3, 3, 3 } for a cubic curve. The control point on the seam of the closed curve cannot be replicated at both ends; it should occur only at the beginning.

To convert from a clamped periodic curve (numKnots = numCtrlPts + Order, ctrlPts replicated, knot multiplicity = order at each end) to a SOLIDWORKS periodic curve, remove all but one of the knots at the beginning of the vector and remove one at the end. Also remove the last control point to avoid the point replication.

 

See Also



Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   CreateBsplineSurface Method (IModeler)
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:



x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: API Help (English only) 2015 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.