Hide Table of Contents

Create Advanced Hole Feature Example (VBA)

This example shows how to create an Advanced Hole feature.

'----------------------------------------------------------------------------
' Preconditions:
' 1. Verify that the specified part document exists.
' 2. Open the Immediate window.
'
' Postconditions:
' 1. Selects near and far side faces of the Advanced Hole.
' 2. Defines an Advanced Hole at a sketch point on the edge of the block
'    with the following:
'    * Countersink near side element
'    * Straight tap near side element
'    * Counterbore far side element
'    * Straight hole far side element
' 3. Gets some near and far side element data for the Advanced Hole.
' 4. Modifies the near side element array to contain a tapered tap element.
' 5. Deletes the Advanced Hole's defining sketch point on the edge of the block.
' 6. Adds two sketch points and creates two Advanced Holes at those locations
'    using the previously defined Advanced Hole.
' 7. Inspect the Immediate window and graphics area.
'
' NOTE: Because the model is used elsewhere, do not save changes.
'---------------------------------------------------------------------------- 

Option Explicit


Dim swApp As SldWorks.SldWorks
Dim swModel As SldWorks.ModelDoc2
Dim feat As Feature
Dim boolstatus As Boolean
Dim swAdvHole_Near_1 As AdvancedHoleElementData
Dim swAdvHole_Near_2 As AdvancedHoleElementData
Dim swAdvHole_Near_3 As AdvancedHoleElementData
Dim swAdvHole_Far_1 As AdvancedHoleElementData
Dim swAdvHole_Far_2 As AdvancedHoleElementData
Dim swCounterSinkNear As CountersinkElementData
Dim swCounterBoreFar As CounterboreElementData
Dim swStraightHoleFar As StraightElementData
Dim swStraightTapNear As StraightTapElementData
Dim swTaperedTapNear As TaperedTapElementData
Dim swFeatureMgr As FeatureManager
Dim ConvFactorAngle, ConvFactorLength As Double
Dim advHoleNearArr(1) As AdvancedHoleElementData
Dim advHoleFarArr(1) As AdvancedHoleElementData
Dim featdata As AdvancedHoleFeatureData
Dim newNearArr(1) As AdvancedHoleElementData
Dim newFarArr(1) As AdvancedHoleElementData
Dim swSketchFeature As Feature
Dim swSelectionManager As SelectionMgr
Dim swSketch As Sketch
Dim swSketchPointArray As Variant
Dim swMaxPointNumber As Long
Dim skPoint As Object
Dim swSketchPoint As Object
Dim swCurrentPointNumber As Long
Dim errors As Long, warnings As Long
Dim jtr As Long
Dim ResultArray As Variant
Dim CalloutString As String
Dim StrDiam As String
Dim strDepth As String
Dim retVal as Boolean
 

Sub main()

    Set swApp = Application.SldWorks
    Set swModel = swApp.OpenDoc6("C:\Users\Public\Documents\SOLIDWORKS\SOLIDWORKS 2018\samples\tutorial\api\block20.sldprt", swDocPART, swOpenDocOptions_Silent, "", errors, warnings)
    Set swFeatureMgr = swModel.FeatureManager

    ConvFactorLength = 25.4 / 1000 'inches to meters
    ConvFactorAngle = (22 / 7) / 180 'degrees to radians
   

    'Select the near and far side faces
    boolstatus = swModel.Extension.SelectByRay(-5.89202612791269E-02, 2.60626824463657E-02, 5.60000000000969E-02, -0.400036026779312, -0.515038074910024, -0.758094294050284, 7.22831189342222E-04, 2, False, 256, 0) 'Near side
    boolstatus = swModel.Extension.SelectByRay(-1.10716643645077E-02, 2.11784489308116E-02, -6.39370439421896E-02, 0.18261953966356, -0.612697461661826, 0.76892907618728, 9.36301020408163E-04, 2, False, 512, 0) 'Far side
   

    'Define near and far side hole elements
   

    'Near side countersink
    Set swAdvHole_Near_1 = swModel.Extension.CreateAdvancedHoleElementData(swAdvWzdGeneralHoleTypes_e.swAdvWzdCounterSink)
    swAdvHole_Near_1.Orientation = swHoleElementOrientation_e.swHoleElementOrientation_Nearside
    swAdvHole_Near_1.Size = "#4"
    swAdvHole_Near_1.Standard = swWzdHoleStandards_e.swStandardAnsiInch
    swAdvHole_Near_1.FastenerType = swWzdHoleStandardFastenerTypes_e.swStandardAnsiInchFlatHead100
    swAdvHole_Near_1.Diameter = ConvFactorLength * 0.225
    swAdvHole_Near_1.BlindDepth = 0.02055794 * ConvFactorLength
    swAdvHole_Near_1.EndCondition = swEndConditions_e.swEndCondBlind
    Set swCounterSinkNear = swAdvHole_Near_1
    swCounterSinkNear.EndConditionOverride = True
    swCounterSinkNear.AngleOverride = False
   

    'Near side straight tap
    Set swAdvHole_Near_2 = swModel.Extension.CreateAdvancedHoleElementData(swAdvWzdGeneralHoleTypes_e.swAdvWzdStraightTap)

    swAdvHole_Near_2.Orientation = swHoleElementOrientation_e.swHoleElementOrientation_Nearside
    swAdvHole_Near_2.Size = "#4-40"
    swAdvHole_Near_2.Standard = swWzdHoleStandards_e.swStandardAnsiInch
    swAdvHole_Near_2.FastenerType = swWzdHoleStandardFastenerTypes_e.swStandardAnsiInchBottomingTappedHole
    swAdvHole_Near_2.Diameter = ConvFactorLength * 0.089
    swAdvHole_Near_2.EndCondition = swEndConditions_e.swEndCondUpToNext
    swAdvHole_Near_2.DiameterOverride = True
    Set swStraightTapNear = swAdvHole_Near_2
    swStraightTapNear.CustomSizing = swStraightTapHoleCustomSizing_e.swStraightTapHoleCustomSizing_TapDrillDiameter
    swStraightTapNear.ThreadClass = swStraightTapHoleThreadClass_e.swStraightTapHoleThreadClass_1B
    swStraightTapNear.ThreadClassOverride = True
   

    'Near side tapered tap
    Set swAdvHole_Near_3 = swModel.Extension.CreateAdvancedHoleElementData(swAdvWzdGeneralHoleTypes_e.swAdvWzdTaperTap)
    swAdvHole_Near_3.Orientation = swHoleElementOrientation_e.swHoleElementOrientation_Nearside
    swAdvHole_Near_3.Size = "1/16"
    swAdvHole_Near_3.Standard = swWzdHoleStandards_e.swStandardAnsiInch
    swAdvHole_Near_3.FastenerType = swWzdHoleStandardFastenerTypes_e.swStandardAnsiInchTaperedPipeTap
    swAdvHole_Near_3.Diameter = ConvFactorLength * 0.266
    swAdvHole_Near_2.BlindDepth = 0.205 * ConvFactorLength
    swAdvHole_Near_3.EndCondition = swEndConditions_e.swEndCondBlind
    swAdvHole_Near_3.DiameterOverride = True
    Set swTaperedTapNear = swAdvHole_Near_3
    swTaperedTapNear.CustomSizing = swTaperedTapCustomSizing_e.swTaperedTapCustomSizing_MinorDiameterwithCosmeticThread
    swTaperedTapNear.ThreadClass = swTaperedTapThreadClass_e.swTaperedTapThreadClass_1
    swTaperedTapNear.ThreadClassOverride = True
    swTaperedTapNear.EndConditionOverride = True
   

    'Far side counterbore
    Set swAdvHole_Far_1 = swModel.Extension.CreateAdvancedHoleElementData(swAdvWzdGeneralHoleTypes_e.swAdvWzdCounterBore)
    swAdvHole_Far_1.Orientation = swHoleElementOrientation_e.swHoleElementOrientation_Farside
    swAdvHole_Far_1.Size = "#8"
    swAdvHole_Far_1.Standard = swWzdHoleStandards_e.swStandardAnsiInch
    swAdvHole_Far_1.FastenerType = swWzdHoleStandardFastenerTypes_e.swStandardAnsiInchBinding
    swAdvHole_Far_1.Diameter = ConvFactorLength * 0.375
    swAdvHole_Far_1.BlindDepth = 0.105 * ConvFactorLength
    swAdvHole_Far_1.EndCondition = swEndConditions_e.swEndCondBlind
    swAdvHole_Far_1.DiameterOverride = True
    Set swCounterBoreFar = swAdvHole_Far_1
    swCounterBoreFar.EndConditionOverride = True
 

    'Far side straight hole
    Set swAdvHole_Far_2 = swModel.Extension.CreateAdvancedHoleElementData(swAdvWzdGeneralHoleTypes_e.swAdvWzdStraight)

    swAdvHole_Far_2.Orientation = swHoleElementOrientation_e.swHoleElementOrientation_Farside
    swAdvHole_Far_2.Size = "1/16"
    swAdvHole_Far_2.Standard = swWzdHoleStandards_e.swStandardAnsiInch
    swAdvHole_Far_2.FastenerType = swWzdHoleStandardFastenerTypes_e.swStandardAnsiInchAllDrillSizes
    swAdvHole_Far_2.Diameter = ConvFactorLength * 0.0625
    swAdvHole_Far_2.BlindDepth = 0.2711 * ConvFactorLength
    swAdvHole_Far_2.EndCondition = swEndConditions_e.swEndCondBlind
    swAdvHole_Far_2.DiameterOverride = True
 

    'Customize the hole callout for this straight element
    StrDiam = swModel.Extension.GetCalloutVariableString(swCalloutVariable_AH_Straight_Diameter)
    strDepth = swModel.Extension.GetCalloutVariableString(swCalloutVariable_AH_Straight_Depth)
    CalloutString = "<MOD-DIAM> " & StrDiam & " " & "<HOLE-DEPTH> " & strDepth
    swAdvHole_Far_2.CalloutString = CalloutString
    Set swStraightHoleFar = swAdvHole_Far_2
   

    'Set the near and far side arrays; stack ordering is from the near and far side faces
    Set advHoleNearArr(0) = swCounterSinkNear
    Set advHoleNearArr(1) = swStraightTapNear
    Set advHoleFarArr(0) = swCounterBoreFar
    Set advHoleFarArr(1) = swStraightHoleFar
   

    Set feat = swFeatureMgr.AdvancedHole((advHoleNearArr), (advHoleFarArr), False, True, ResultArray)
   

    'Get the near and far side element data
    Set featdata = feat.GetDefinition
    featdata.AccessSelections swModel, Nothing
    Debug.Print "Number of near side hole elements: " & featdata.NearSideElementsCount
    Debug.Print "Number of far side hole elements: " & featdata.FarSideElementsCount
    Set swCounterSinkNear = featdata.GetNearSideElements(0)
    Set swCounterBoreFar = featdata.GetFarSideElements(0)
    Debug.Print "Near side countersink:"
    Debug.Print "   Hole element type as defined in swAdvWzdGeneralHoleTypes_e: " & swCounterSinkNear.ElementType
    Debug.Print "   Size as defined on the Advanced Hole PropertyManager page: " & swCounterSinkNear.Size
    Debug.Print "   Standard as defined in swWzdHoleStandards_e: " & swCounterSinkNear.Standard
    Debug.Print "   Fastener type as defined in swWzdHoleStandardFastenerTypes_e: " & swCounterSinkNear.FastenerType
    Debug.Print "   Diameter in m: " & swCounterSinkNear.Diameter
    Debug.Print "   Blind depth in m: " & swCounterSinkNear.BlindDepth
    Debug.Print "   Orientation as defined in swHoleElementOrientation_e: " & swCounterSinkNear.Orientation
    Debug.Print "   End condition as defined in swEndConditions_e: " & swCounterSinkNear.EndCondition
 

    Debug.Print "Far side straight:"
    Debug.Print "   Hole element type as defined in swAdvWzdGeneralHoleTypes_e: " & swStraightHoleFar.ElementType
    Debug.Print "   Size as defined on the Advanced Hole PropertyManager page: " & swStraightHoleFar.Size
    Debug.Print "   Standard as defined in swWzdHoleStandards_e: " & swStraightHoleFar.Standard
    Debug.Print "   Fastener type as defined in swWzdHoleStandardFastenerTypes_e: " & swStraightHoleFar.FastenerType
    Debug.Print "   Diameter in m: " & swStraightHoleFar.Diameter
    Debug.Print "   Diameter override? " & swStraightHoleFar.DiameterOverride
    Debug.Print "   Blind depth in m: " & swStraightHoleFar.BlindDepth
    Debug.Print "   Orientation as defined in swHoleElementOrientation_e: " & swStraightHoleFar.Orientation
    Debug.Print "   End condition as defined in swEndConditions_e: " & swStraightHoleFar.EndCondition
    Debug.Print "   Customized hole callout: " & swStraightHoleFar.CalloutString

   
    'Modify the near and far side element arrays
    Set newNearArr(0) = swTaperedTapNear
    Set newNearArr(1) = swStraightTapNear
    'Set newFarArr(0) = swCounterBoreFar
    'Set newFarArr(1) = swStraightHoleFar
    featdata.SetNearSideElements newNearArr
    'featdata.SetFarSideElements newFarArr
    feat.ModifyDefinition featdata, swModel, Nothing
   

    'Delete the first point used to define the Advanced Hole
    Set swSketchFeature = feat.GetFirstSubFeature
    swSketchFeature.Select2 False, 0
    swModel.EditSketch
    Set swSelectionManager = swModel.SelectionManager
    Set swSketch = swSketchFeature.GetSpecificFeature2()
    swSketchPointArray = swSketch.GetSketchPoints2()
    swMaxPointNumber = UBound(swSketchPointArray)
    For swCurrentPointNumber = 0 To swMaxPointNumber Step 1
       Set swSketchPoint = swSketchPointArray(swCurrentPointNumber)
       retval = swSelectionManager.AddSelectionListObject(swSketchPoint, Nothing)
       swModel.EditDelete
    Next swCurrentPointNumber
   

    'Create points for multiple Advanced Hole locations
    Set skPoint = swModel.SketchManager.CreatePoint(-3.19158789518497E-02, 3.44489966898323E-02, 0.05600000000004)
    Set skPoint = swModel.SketchManager.CreatePoint(-4.94104502066557E-02, 8.0156770060853E-03, 5.60000000000969E-02)
   

    swModel.SketchManager.InsertSketch True

End Sub



Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   reate Advanced Hole Feature Example (VBA)
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:



x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: API Help (English only) 2018 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.