Function Parameterization() As System.Object

Dim instance As ISurface Dim value As System.Object value = instance.Parameterization()

System.object Parameterization()

System.Object^ Parameterization();

The return value is the following array of 11 doubles:

[ uRange[2], vRange[2], uBoundType, vBoundType, uProps[2], vProps[2], numProps ]

where:

uRange[2] = array of two doubles describing the low and high range, respectively, for U.

vRange[2] = array of two doubles describing the low and high range, respectively, for V.

uBoundType = two integers packed into a double. Each integer describes the behavior at the start and at the end of the U range. Valid values and their meanings are:

13733 - Infinite

13734 - Extendable

13735 - Not Extendable

13701 - Periodic

13736 - Periodic, but not continuously differentiable across the boundary

13741 - Degenerate

If the behavior at the start of the U range is Degenerate', then the V parameter is degenerate when U = urange[0]'. The derivative of the parameterization function with respect to v is 0whenever u = urange[0]', for all values of v, and the parameter curve corresponding to u = urange[0]' degenerates to a single point. A parameterization can only degenerate at the end of its range, unless the surface is a type of Bsurface.

vBoundType = two integers packed into a double. Each integer describes the behavior at the start and end of the V range. For valid values and their meanings, see description of uBoundType.

uProps[2] = four integers packed into two doubles representing U parameterization properties. The uProps array of two doubles will contain a total of one or more integer values with a maximum of four. Valid values and their meanings are:

13701 - Periodic parameterization.

13737 - All derivatives continuous.

13738 - All derivatives non necessarily continuous.

13739 - Linear. Corresponding parameter is proportional to the distance along a straight line. Straight line corresponds to a constant value of the other parameter.

13740 - Circular. Corresponding parameter represents an angle around a circle. Circle corresponds to a constant value of the other parameter.

13746 - Bounds at the ends of the parameter range are coincident.

vProps[2] = four integers packed into two doubles representing V parameterization properties. The vProps array of two doubles will contain a total of one or more integer values with a maximum of four. For valid values and their meanings, see description of uProps.

numProps = two integers packed into a double. Each integer represents the number of properties returned in uProps and vProps, respectively.

If a surface is periodic in one direction (that is, cylinder, cone, torus (apple and lemon shapes), spheres), then U is the periodic direction.

The -10000 to 10000 parameter range is the modeling limit for the modeler. This means that the values are effectively infinite in size. To get the parameter range from a given face, use IFace2::GetBox or IFace2::IGetBox, ISurface::GetClosestPointOn or ISurface::IGetClosestPointOn, and ISurface::ReverseEvaluate or ISurface::IReverseEvaluate. These methods provide a true parameter range that the face is using on the surface.

Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

Thank you for your comments. We will contact you if we have questions regarding your feedback.

Sincerely,The SOLIDWORKS Documentation Team

Print Topic

Select the scope of content to print:

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

Web Help Content Version: API Help (English only) 2018 SP05 To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help. To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.