Example of Length and Angle Custom Properties

Angle1 and Angle2 are the angles between the normal of the cut face and the centerline of the body.

Comparison of Components Suppression States

... be edited in-context Load and rebuild speed Normal...Normal...Normal Normal Faster Faster 1 In-context ...

Default Options - Plot - Drop Test Study

SX: X Normal stress...SY: Y Normal stress...SZ: Z Normal stress TXY: Shear in Y direction on YZ plane TXZ:...

Orientation/Twist Type - Follow Path

Profiles always maintain a normal to the path...The normal of the plane, the Z-axis, is the...The normal of the plane, the Z-axis, is the

Orientation

Click Normal To (View Orientation flyout &#8211 Heads-up View toolbar...If you click Normal To again, the model flips 180 &#176 See Orienting a Model to XYZ Coordinates for another way to display a model in Normal To view...Click Normal To (View Orientation flyout &#8211 Heads-up View toolbar...

Output of Linear Static Analysis

... reaction force EPSX = X Normal strain...EPSY = Y Normal strain...EPSZ = Z Normal strain GMXY = Shear ...

Wrap Feature

The sketch plane must be tangent to the face, allowing the face normal and the sketch normal to be parallel at the closest point...For a plane, the pull direction is normal to the plane...To wrap the sketch normal to the sketch plane, leave Pull Direction blank

Applying Pressure

The program applies pressure loads normal to each face...Select: Normal to selected face to apply the pressure in the direction normal to each selected face

Orientation

. Normal To is normal (perpendicular) to the sketch plane or the selected plane. To access the ...

Example of Boundary Surface Alignment

... section normal...Aligns the boundary surface iso parameters normal to the selected curve. Align with ...

Allow Reduced Angle Option

The normal of one or more side faces adjacent to the edge and the faces being drafted is nearly perpendicular to the Direction of Pull...model type and condition, select the Allow reduced angle check box when the maximum angle between the pull direction and the normal of the steep face...The red arrow represents the surface normal at its maximum angle to the pull

Performance Settings

Performance Options &#8211 High quality for normal view mode...Performance Options &#8211 High quality for normal view mode

Applying Forces

Select: Normal to apply the force in the direction normal to each selected face...Selected direction to apply the specified force value to each face in the direction of its normal

Flat Pattern Improvements

... for manufacturing. You can also turn off the Normal cut option. This minimizes the weldment gap ...

Defining Nonuniform Force Loads

Normal to plane...To apply nonuniform force normal to a face...Normal force to the selected faces is applied by default

Reference Triad

... an axis See the view normal to the screen...Select an axis that is normal to the screen Change the ...

Extrude Direction Along Vector

You can extrude 2D and 3D sketches normal to the face, or you can select a Direction of Extrusion

Defining Uniform Pressure Loads

To apply a uniform pressure normal to a face...On the Type tab under Type, select Normal to selected face...If you select a face or a plane for direction, select one of the following components: Along Plane Dir 1 , Along Plane Dir 2 , or Normal to Plane...

Example of Rib Feature Sketches

Rib feature applied using Normal to Sketch as the Extrusion direction...Rib feature applied using Normal to Sketch as the Extrusion direction

Edit Sketch Message PropertyManager

In new sketches, the plane rotates into Normal to orientation and you can proceed with the sketch.

Contact/Friction Force

Normal and friction forces develop on faces of components with No Penetration, Shrink Fit and Virtual Wall contact types...Normal...This total force is the resultant of the Normal and Friction forces calculated at each node of the selected entities

Viewing Results for Edge Weld Connectors

You can also view weld results along the weld seam such as: weld size, weld throat size, normal force, shear-weld axis force, shear-surface normal

Plane Properties PropertyManager

Controls the angle between the projection of the normal on the x-y plane and the X direction...Controls the angle between the normal and it's projection on the x-y plane

Decals Mapping Projection

Projection mapping places the decal on a plane normal to the view and projects the each pixel of the image in a straight, parallel ray to match the...edge, a reference plane is created normal to axis or edge at its end point

Ply Angle

and the Z direction is normal to the ply surface...The green arrow is aligned normal to the surface stripes...The blue arrow is normal to the surface