Refine your search

1-25 of 243 results. Page 1 - next page          Results per page:

Default Options - Plot - Static Study

SY: Y Normal stress...SZ: Z Normal stress...SX: X Normal stress

Simulation  >  Simulation Options

Using Normal to Origin Feature

The Normal-to origin feature option reorients the direction of measurement to be normal (perpendicular) to the measure-From feature of the measurement...With Normal to origin feature cleared, the evaluation dimension Y is taken along the Y axis...With Normal to origin feature selected, the evaluation dimension N is taken normal to the origin feature

Tolerancing > TolAnalyst > Analyzing the Results

Stress

The state of stresses at a point is fully described by the following components: SX Stress in the X-direction acting normal to the YZ-plane SY Stress in the Y-direction acting normal to the XZ-plane SZ Stress in the Z-direction acting normal to the XY-plane TXY Stress in the Y-direction acting on the plane normal to the X-direction (YZ-plane) TYX Stress in the X-direction acting on the plane normal to the Y-direction (XZ-plane) TXZ Stress in the Z-direction acting on the plane normal to the X...

Default Options - Plot - Nonlinear Study

SY: Y Normal stress...SZ: Z Normal stress...SX: X Normal stress

Simulation  >  Simulation Options

Normal Cut

When adding a cut to a folded sheet metal part, select Normal cut to ensure that the cut is created normal to the sheet metal thickness

Normal To Command

You can use the Normal To command to orient a model normal to the nearest global XYZ coordinates...To orient a model normal to the nearest global XYZ coordinates

What's New > Fundamentals

Reference Plane Normal to Edge

You can sketch on a reference plane, created automatically, normal to an edge...To sketch on a reference plane normal to an edge...A reference plane normal to the selected edge is created at the end point of the edge closest to the selected area

Sketching > Sketch Options

Orientation

Click Normal To (View Orientation flyout &#8211 Heads-up View toolbar...If you click Normal To again, the model flips 180 &#176 See Orienting a Model to XYZ Coordinates for another way to display a model in Normal To view...Click Normal To (View Orientation flyout &#8211 Heads-up View toolbar...

SOLIDWORKS Fundamentals  >  Display

Maximum Normal Stress Criterion

The maximum normal stress criterion also known as Coulomb’s criterion is based on the Maximum normal stress theory

Simulation > Checking Stress Results > Failure Criteria

Edge Weld Definitions

Surface Normal, Us: Axis is normal to the top surface of the shell of the terminated part...Joint Normal Force A component of the weld force (Tj) acting normal to the intersecting shell edge of the terminated part along the weld joint normal axis, Uj

Simulation > Loads and Restraints > Connectors > Edge Weld

Loft PropertyManager

Applies a tangency constraint normal to the start or end profile...Draft angle (Available with Direction Vector or Normal to Profile selected for Start or End constraint...Applies a tangency constraint normal to the plane of the guide curve

Parts and Features  >  Features

Force

For example, if you apply a force that is normal to a full cylindrical face, the vector sum of the applied forces is zero...Normal to plane...Sets the value of the force component normal to the plane or face

Simulation  >  Loads and Restraints

Two fixed normal motions

Two fixed normal motions

Pressure

Pressure can be applied normal to the selected faces or it can be applied in some other direction...For example, hydrostatic pressure is normal to faces, while the snow on a sloped roof applies a vertical pressure and a wind blowing horizontally applies a horizontal pressure...Applies pressure in the direction normal to each face or shell edge you select

Simulation  >  Loads and Restraints

Drop Test Setup

If you select a reference plane or planar face, the velocity is applied in the direction normal to the reference plane or the planar face...If you select a reference plane or planar face, the gravity is applied in the direction normal to the reference plane or the planar face...Sets the stiffness per unit area normal to the impact plane

Simulation  >  Simulation Studies

Orienting a Model to XYZ Coordinates

You can use the Normal To command to orient a model normal to the nearest global XYZ coordinates...To orient a model normal to the nearest global XYZ coordinates

SolidWorks Fundamentals > Display > Manipulating Views

Default Options - Plot - Drop Test Study

SY: Y Normal stress...SZ: Z Normal stress...SX: X Normal stress

Simulation  >  Simulation Options

Video_Camera Normal To

Sweep PropertyManager

To keep the tool body perpendicular to a reference as it follows a helix path, select Direction Vector for Path alignment type, then select a direction to which the tool body remains perpendicular, for example, the normal to the planar end face of a cylinder...Aligns the profile normal to the path...Create the sweep normal to the path at the start

Parts and Features  >  Features

Orientation/Twist Type - Follow Path

Profiles always maintain a normal to the path...The normal of the plane, the Z-axis, is the tangent of the path at that point

Parts and Features > Features > Sweeps > Sweeps Options

Parting Surface PropertyManager

Sets the parting surface normal to the surface of the parting line...Reverse Alignment (Available for Normal to surface when two faces adjacent to the parting edge are almost parallel.) Changes the face to which the parting surface is normal

Mold Design  >  Parting Surfaces

Using a Model Face

You can prescribe the translations in directions 1 and 2 of the face as well as in the direction normal to the face...Along face direction 1 Along face direction 2 Normal to face Rotations (for shells and beams only...About face direction 1 About face direction 2 About normal to face

Simulation > Loads and Restraints > Fixtures > Using Reference Geometry

Defining Nonuniform Force Loads

If you select a face or a plane for direction, specify at least one of the following force components: Along plane Dir 1 , Along plane Dir 2 , or Normal to plane...To apply nonuniform force normal to a face

Simulation  >  Loads and Restraints

Performing Failure Analysis Using Mohr-Coulomb Stress Criterion

If you selected Max normal or Mohr-Coulomb criterion for a beam material, the software uses the tensile strength as the allowable stress...The Max stress in the model box shows the maximum normal stresses (1st and 2nd principal) in the model

Simulation > Checking Stress Results

Wrap Feature

The sketch plane must be tangent to the face, allowing the face normal and the sketch normal to be parallel at the closest point...For a plane, the pull direction is normal to the plane...To wrap the sketch normal to the sketch plane, leave Pull Direction blank

Parts and Features  >  Features