Create Linear Dynamic Study Example (VB.NET)

'-----------------------------------------------------------------------------
' Preconditions:
' 1. Add the SolidWorks Simulation as an add-in
'    (in SolidWorks, click Tools > Add-ins > SolidWorks Simulation).
' 2. Add the SolidWorks Simulation primary interop assembly as
'    a reference (in the IDE's Project Explorer, right-click
'    the project name, select Add Reference, click the Browse tab,
'    navigate to the install_dir\api\redist\CLR2 folder and
'    select SolidWorks.Interop.cosworks.dll).
' 3. Modify install_dir to point to your SolidWorks installation.
'
' Postconditions:
' 1. Linear_Dynamic_1.sldprt is opened.
' 2. A linear dynamic study is created.
' 3. An harmonic analysis is run.
' 4. The Dynamic_Harmonic simulation study tree contains the following:
'    * Nonlinear_Static_2 (shell)
'    * Connections
'    * Fixtures
'      ** Fixed-1
'      ** Fixed-2
'    * External Loads
'      ** Pressure-1
'      ** Base Excitation-1
'      ** Distributed Mass-1
'    * Mesh
'    * Damping (-Modal damping-)
'    * Result Options
'    * Results
'      ** Stress1 (-vonMises-)
'      ** Displacement1 (-Res disp-)
'      ** Velocity1 (-VX-)
' 5. Right-click on the Stress1 or Displacement1 plot in the Results folder
'    and select Show to plot the results in color in the graphics area.
' 6. Inspect the Immediate Window for:
'    * Dynamic study options
'    * Study result options
'    * Uniform base excitation data
'    * Total distributed mass
'    * Worst Jacobian ratio
'    * Study results
'      * Min/Max URES resultant displacements at maximum solution step
'        ** Node with minimum value
'        ** Minimum value
'        ** Node with maximum value
'        ** Maximum value
'      * Min/Max von Mises stresses at maximum solution step
'        ** Node with minimum value
'        ** Minimum value
'        ** Node with maximum value
'        ** Maximum value
'      * Min/Max velocities at maximum solution step
'        ** Node with minimum value
'        ** Minimum value
'        ** Node with maximum value
'        ** Maximum value
'      * Min/Max accelerations at maximum solution step
'        ** Node with minimum value
'        ** Minimum value
'        ** Node with maximum value
'        ** Maximum value
' 7. Inspect c:\temp for saved solution step, displacement, velocity,
'    and stress result files.
'
' NOTES: Because the model is used elsewhere,
'        do not save any changes when closing it.
'--------------------------------------------------------------------
Imports SolidWorks.Interop.sldworks
Imports SolidWorks.Interop.swconst
Imports SolidWorks.Interop.cosworks
Imports System.Runtime.InteropServices
Imports System
Imports System.Diagnostics

Partial Class SolidWorksMacro

    Sub main()

        Dim Part As ModelDoc2
        Dim COSMOSWORKS As Object
        Dim CWAddinCallBack As CwAddincallback
        Dim ActDoc As CWModelDoc
        Dim StudyMngr As CWStudyManager
        Dim Study As CWStudy
        Dim ShellMgr As CWShellManager
        Dim ShellMat As CWMaterial
        Dim LBCMgr As CWLoadsAndRestraintsManager
        Dim CWBaseExcitationU As CWBaseExcitation
        Dim CWDistribMass As CWDistributedMass
        Dim CWBaseExcitationEntity As Object
        Dim CWDirectionEntity As Object
        Dim longstatus As Long
        Dim longwarnings As Long
        Dim errCode As Long
        Dim nStep As Long
        Dim pDisp5 As Object
        Dim DispArray1(0) As Object, DispArray2(0) As Object, DispArray3(0) As Object, DispArray4(1) As Object
        Dim Disp As Object, Stress As Object, Velocity As Object, Acceleration As Object
        Dim sStudyName As String
        Dim ResultOptions As CWStudyResultOptions
        Dim DampingOptions As CWDampingOptions
        Dim DampingRatios(8) As Object
        Dim i As Long

        'Tolerances and baselines
        Const MeshEleSize As Double = 26.5868077635828 'mm
        Const MeshTol As Double = 1.32934038817914 'mm

        'PID to call
        Dim PIDCollection As New Collection
        PIDCollection = PIDInitializer()

        'Open document
        Part = swApp.OpenDoc6("install_dir\samples\tutorial\api\LinearDynamic.SLDPRT", swDocumentTypes_e.swDocPART, 1, "", longstatus, longwarnings)
        If Part Is Nothing Then ErrorMsg(SwApp, "Failed to open LinearDynamic.SLDPRT.")

        'Addin callback
        CWAddinCallBack = SwApp.GetAddInObject("SldWorks.Simulation")
        If CWAddinCallBack Is Nothing Then ErrorMsg(SwApp, "Failed to get CWAddinCallBack object.")
        COSMOSWORKS = CWAddinCallBack.COSMOSWORKS
        If COSMOSWORKS Is Nothing Then ErrorMsg(SwApp, "Failed to get COSMOSWORKS object.")

        'Get active document
        ActDoc = COSMOSWORKS.ActiveDoc()
        If ActDoc Is Nothing Then ErrorMsg(SwApp, "Failed to get active document.")

        'Create a dynamic harmonic study
        StudyMngr = ActDoc.StudyManager()
        If StudyMngr Is Nothing Then ErrorMsg(SwApp, "Failed to get StudyManager object.")

        sStudyName = "Dynamic_Harmonic"
        Study = StudyMngr.CreateNewStudy3(sStudyName, swsAnalysisStudyType_e.swsAnalysisStudyTypeDynamic, swsDynamicStudySubOption_e.swsDynamicHarmonic, errCode)

        Debug.Print("Linear dynamic study with harmonic analysis")
        Debug.Print("")
        Debug.Print("Dynamic study options...")
        Dim DynStudyOptions As CWDynamicStudyOptions
        DynStudyOptions = Study.DynamicStudyOptions
        Dim freqOption As Long
        Dim freqValue As Double
        Dim bChecked As Long
        DynStudyOptions.GetFrequencyOption(freqOption, freqValue)
        Debug.Print("  Frequency option (swsFrequencyStudyOption_e): " & freqOption)
        Debug.Print("  No. of frequencies or upper-bound frequency: " & freqValue)
        DynStudyOptions.GetFrequencyShiftOption(bChecked, freqValue)
        Debug.Print("  Is frequency shift enabled (0=no, 1=yes)? " & bChecked)
        Debug.Print("  Frequency shift: " & freqValue)
        DynStudyOptions.IncompatibleBondingOption = 0 ' automatic
        DynStudyOptions.UseSoftSpring = 0 ' do not use soft springs to stabilize model
        DynStudyOptions.ResultFolderPath = "c:\temp"
        DynStudyOptions.SolverType = 2 ' FFEPlus
        Debug.Print("  Harmonic bandwidth: " & DynStudyOptions.HarmonicBandwidth)
        Debug.Print("  Harmonic frequency lower limit: " & DynStudyOptions.HarmonicFrequencyLowerLimit)
        Debug.Print("  Harmonic frequency upper limit: " & DynStudyOptions.HarmonicFrequencyUpperLimit)
        Debug.Print("  Harmonic frequency units (swsFrequencyUnit_e): " & DynStudyOptions.HarmonicFrequencyUnits)
        Debug.Print("  Harmonic interpolation (swsInterpolationType_e): " & DynStudyOptions.HarmonicInterpolation)
        Debug.Print("  Harmonic number of points for each frequency: " & DynStudyOptions.HarmonicNoOfPoints)
        Debug.Print("")

        'Set study result options
        Debug.Print("Study result options...")
        ResultOptions = Study.StudyResultOptions
        ResultOptions.SaveResultsForSolutionStepsOption = 1 ' save solution step results
        ResultOptions.SaveDisplacementsAndVelocitiesOption = 1 ' save displacements and velocities
        ResultOptions.SaveStresses = 1 ' save stresses
        ' Solution step set #1
        errCode = ResultOptions.SetSolutionStepsSetInformation(1, 10, 100, 3)
        Debug.Print("  Set solution steps set #1 (10-100, inc=3)? (0=success): " & errCode)
        ' Solution step set #3
        errCode = ResultOptions.SetSolutionStepsSetInformation(3, 100, 1000, 5)
        Debug.Print("  Set solution steps set #3 (100-1000, inc=5)? (0=success): " & errCode)
        Debug.Print("")

        'Set damping options
        DampingOptions = Study.DampingOptions
        DampingOptions.DampingType = 0 'Modal damping
        DampingRatios(0) = 1
        DampingRatios(1) = 5
        DampingRatios(2) = 3.45
        DampingRatios(3) = 6
        DampingRatios(4) = 15
        DampingRatios(5) = 15
        DampingRatios(6) = 16
        DampingRatios(7) = 25
        DampingRatios(8) = 34.5

        errCode = DampingOptions.SetDampingRatios(3, (DampingRatios))
        DampingOptions.ComputeFromMaterialDamping = 0 ' do not use the material damping ratio

        'Create variant arrays
        DispArray1(0) = SelectByPID(Part, "selection1", PIDCollection)
        DispArray2(0) = SelectByPID(Part, "selection1", PIDCollection)
        DispArray3(0) = SelectByPID(Part, "selection2", PIDCollection)
        DispArray4(0) = SelectByPID(Part, "selection3", PIDCollection)
        DispArray4(1) = SelectByPID(Part, "selection4", PIDCollection)

        'Get Edge-1 by persistent ID
        CWBaseExcitationEntity = SelectByPID(Part, "selection3", PIDCollection)

        'Get Axis1 by persistent ID
        CWDirectionEntity = SelectByPID(Part, "selection5", PIDCollection)
        pDisp5 = SelectByPID(Part, "selection5", PIDCollection)

        'Add materials
        ShellMgr = Study.ShellManager
        If ShellMgr Is Nothing Then ErrorMsg(SwApp, "Failed to get ShellMgr object.")

        Dim CWFeatObj1 As CWShell
        CWFeatObj1 = ShellMgr.GetShellAt(0, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to get shell component.")
        ShellMat = CWFeatObj1.GetDefaultMaterial
        ShellMat.MaterialUnits = 0
        Call ShellMat.SetPropertyByName("EX", 2000000000000.0#, 0)
        Call ShellMat.SetPropertyByName("NUXY", 0.25, 0)
        errCode = CWFeatObj1.SetShellMaterial(ShellMat)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to apply material.")

        Call CWFeatObj1.ShellBeginEdit()
        CWFeatObj1.Formulation = 1 ' thick shell
        CWFeatObj1.ShellUnit = 1 ' centimeters
        CWFeatObj1.ShellThickness = 5 ' 5 cm
        CWFeatObj1.ShellOffsetOption = 3 ' specify reference surface
        CWFeatObj1.ShellOffsetValue = 0.3
        errCode = CWFeatObj1.ShellEndEdit
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to create shell.")
        CWFeatObj1 = Nothing

        'Get loads and restraints manager
        LBCMgr = Study.LoadsAndRestraintsManager
        If LBCMgr Is Nothing Then ErrorMsg(SwApp, "Failed to get LoadsAndRestraintsManager.")

        'Create normal pressure
        Dim CWFeatObj2 As CWPressure
        CWFeatObj2 = LBCMgr.AddPressure(0, (DispArray2), Nothing, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to create normal pressure.")
        Call CWFeatObj2.PressureBeginEdit()
        CWFeatObj2.Unit = 0
        CWFeatObj2.Value = 4000000.0#
        errCode = CWFeatObj2.PressureEndEdit
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to apply normal pressure value.")
        CWFeatObj2 = Nothing

        'Add Restraints
        Dim CWFeatObj3 As CWRestraint
        CWFeatObj3 = LBCMgr.AddRestraint(0, (DispArray3), pDisp5, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to create first restraint.")
        Call CWFeatObj3.RestraintBeginEdit()
        Call CWFeatObj3.SetTranslationComponentsValues(0, 0, 1, 0.0#, 0.0#, 0.0#)
        Call CWFeatObj3.SetRotationComponentsValues(0, 0, 0, 0.0#, 0.0#, 0.0#)
        CWFeatObj3.Unit = 2
        errCode = CWFeatObj3.RestraintEndEdit
        If errCode <> 0 Then ErrorMsg(SwApp, "First RestraintEndEdit failed.")

        CWFeatObj3 = LBCMgr.AddRestraint(0, (DispArray4), pDisp5, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to create second restraint.")
        Call CWFeatObj3.RestraintBeginEdit()
        Call CWFeatObj3.SetTranslationComponentsValues(0, 1, 0, 0.0#, -0.0#, 0.0#)
        Call CWFeatObj3.SetRotationComponentsValues(1, 0, 1, -0.0#, 0.0#, -0.0#)
        CWFeatObj3.Unit = 2
        errCode = CWFeatObj3.RestraintEndEdit
        If errCode <> 0 Then ErrorMsg(SwApp, "Second RestraintEndEdit failed.")
        CWFeatObj3 = Nothing

        'Add uniform base excitation
        CWBaseExcitationU = LBCMgr.AddUniformBaseExcitation(2, CWBaseExcitationEntity, 1, 1, 2.3, 1, 3.4, 1, 4.5, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Adding uniform base excitation failed.")

        Debug.Print("Uniform base excitation type (swsBaseExcitationType_e): " & CWBaseExcitationU.BaseExcitationType)
        Dim bdir1 As Long, bdir2 As Long, bdir3 As Long
        CWBaseExcitationU.GetExcitationDirections(bdir1, bdir2, bdir3)
        Debug.Print("Excitation in...")
        Debug.Print("  Direction 1 (1=true)? " & bdir1)
        Debug.Print("  Direction 2 (1=true)? " & bdir2)
        Debug.Print("  Direction 3 (1=true)? " & bdir3)
        Dim dval1 As Double, dval2 As Double, dval3 As Double
        CWBaseExcitationU.GetExcitationDirectionValues(dval1, dval2, dval3)
        Debug.Print("Excitation value in swsUnit_e units...")
        Debug.Print("  Direction 1: " & dval1)
        Debug.Print("  Direction 2: " & dval2)
        Debug.Print("  Direction 3: " & dval3)
        Dim curveData As Object
        curveData = CWBaseExcitationU.GetTimeOrFrequencyCurve 'variation with frequency data
        Debug.Print("Acceleration excitation variation with frequency data")
        Debug.Print("(number of points, x1, y1, x2, y2, ...xn, yn):")
        For i = 0 To UBound(curveData)
            Debug.Print(curveData(i))
        Next
        Debug.Print("Phase angle: " & CWBaseExcitationU.PhaseAngle)
        Debug.Print("Phase angle unit (swsPhaseAngleUnit_e): " & CWBaseExcitationU.PhaseAngleUnit)
        Debug.Print("Units (depends on type of base excitation): " & CWBaseExcitationU.Unit)
        Debug.Print("")

        'Add distributed mass
        CWDistribMass = LBCMgr.AddDistributedMass((DispArray2), 0, 1, errCode)
        Debug.Print("Total distributed mass: " & CWDistribMass.TotalMass)
        Debug.Print("  Units (swsUnitSystem_e): " & CWDistribMass.Units)
        Debug.Print("")

        'Create mesh
        Dim CWFeatObj4 As CWMesh
        CWFeatObj4 = Study.Mesh
        If CWFeatObj4 Is Nothing Then ErrorMsg(SwApp, "Failed to create Mesh object")
        CWFeatObj4.MesherType = 0
        CWFeatObj4.Quality = 1

        errCode = Study.CreateMesh(0, MeshEleSize, MeshTol)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to create Mesh.")
        Debug.Print("Worst Jacobian ratio for the mesh: " & CWFeatObj4.GetWorstJacobianRatio)
        Debug.Print("")

        'Run analysis
        errCode = Study.RunAnalysis
        If errCode <> 0 Then ErrorMsg(SwApp, "Analysis failed with error code " & errCode & " - " & ProcErrCode(errCode))

        'Get results
        Dim CWFeatObj5 As CWResults
        CWFeatObj5 = Study.Results
        If CWFeatObj5 Is Nothing Then ErrorMsg(SwApp, "Failed to get Results object.")

        Debug.Print("Study results...")
        nStep = CWFeatObj5.GetMaximumAvailableSteps
        Debug.Print("  Maximum available steps: " & nStep)

        'Get algebraic minimum/maximum resultant displacements
        Disp = CWFeatObj5.GetMinMaxDisplacement(3, nStep, Nothing, 0, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to get displacement results.")
        Debug.Print("  Min/Max URES Resultant Displacements (Node, Min, Node, Max):")
        For i = 0 To UBound(Disp)
            Debug.Print(Disp(i))
        Next
        Debug.Print("")

        'Get algebraic minimum/maximum Von Mises stresses
        Stress = CWFeatObj5.GetMinMaxStress(9, 0, nStep, Nothing, 3, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to get stress results.")
        Debug.Print("  Algebraic Min/Max von Mises Stresses (Node, Min, Node, Max):")
        For i = 0 To UBound(Stress)
            Debug.Print(Stress(i))
        Next
        Debug.Print("")

        'Get algebraic minimum/maximum velocities
        Velocity = CWFeatObj5.GetMinMaxVelocity(0, nStep, CWDirectionEntity, 0, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to get velocity results.")
        Debug.Print("  Algebraic Min/Max Velocities (Node, Min, Node, Max):")
        For i = 0 To UBound(Velocity)
            Debug.Print(Velocity(i))
        Next
        Debug.Print("")

        'Get algebraic minimum/maximum accelerations
        Acceleration = CWFeatObj5.GetMinMaxAcceleration(0, nStep, CWDirectionEntity, 0, errCode)
        If errCode <> 0 Then ErrorMsg(SwApp, "Failed to get acceleration results.")
        Debug.Print("  Algebraic Min/Max Accelerations (Node, Min, Node, Max):")
        For i = 0 To UBound(Acceleration)
            Debug.Print(Acceleration(i))
        Next

        CWFeatObj5 = Nothing

    End Sub

    Sub ErrorMsg(ByVal SwApp As Object, ByVal Message As String)
        SwApp.SendMsgToUser2(Message, 0, 0)
        SwApp.RecordLine("'*** WARNING - General")
        SwApp.RecordLine("'*** " & Message)
        SwApp.RecordLine("")
    End Sub

    Function SelectByPID(ByVal Part As ModelDoc2, ByVal PIDName As String, ByVal PIDCollection As Collection) As Object
        Dim PID() As Byte
        Dim PIDVariant As Object
        Dim PIDString As String
        Dim i As Integer
        Dim SelObj As Object

        'Get the string from the collection
        PIDString = ""
        PIDString = PIDCollection.Item(PIDName)

        'Parse the string into an array
        PIDVariant = Split(PIDString, ",")
        ReDim PID(UBound(PIDVariant))

        'Change to a byte array
        For i = 0 To (UBound(PIDVariant) - 1)
            PID(i) = PIDVariant(i)
        Next i

        'Select the entity
        SelObj = Part.Extension.GetObjectByPersistReference((PID))
        SelectByPID = SelObj
        SelObj = Nothing
    End Function

    Function PIDInitializer() As Collection

        Dim PIDCollection As New Collection
        Dim selection1 As String
        Dim selection2 As String
        Dim selection3 As String
        Dim selection4 As String
        Dim selection5 As String
  

   'Pie face
    selection1 = "68,20,0,0,3,0,0,0,255,254,255,0,0,0,0,0,255,255,1,0,11,0,109,111,70,97,99,101,82,101,102,95,99,1,0,0,0,0,0,0,0,5,0,0,0,4,2,0,0,0,0,0,0,125,195,148,37,173,73,178,84,125,195,148,37,173,73,178,84,0,0,255,255,1,0,23,0,109,111,70,114,111,109,83,107,116,69,110,116,83,117,114,102,73,100,82,101,112,95,99,0,0,255,255,1,0,6,0,109,111,70,82,95,99,255,255,1,0,13,0,109,111,69,120,116,79,98,106,101,99,116,95,99,255,255,1,0,17,0,109,111,67,83,116,114,105,110,103,72,97,110,100,108,101,95,99,255,254,255,92,75,0,58,0,92,0,97,0,112,0,105,0,92,0,72,0,69,0,76,0,80,0,92,0,83,0,97,0,109,0,112,0,108,0,101,0,32,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,83,0,105,0,109,0,117,0,108,0,97,0,116,0,105,0,111,0,110,0,92,0,50,0,48,0,49,0,50,0,92,0,65,0,117,0,116,0,111,0,84,0,101,0,115,0,116,0,70,0,105,0,108,0,101,0,115,0,92,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,115,0,92,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,46,0,83,0,76,0,68,0,80"
    selection1 = selection1 & ",0,82,0,84,0,9,128,255,254,255,13,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,2,0,0,141,213,96,79,0,0,112,0,97,0,0,0,0,0,0,0,0,0,0,0,0,0,255,254,255,7,68,0,101,0,102,0,97,0,117,0,108,0,116,0,0,0,0,0,0,0,0,0,100,0,100,0,30,0,0,0,252,214,96,79,1,0,0,0,255,255,1,0,16,0,109,111,84,111,112,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,255,255,1,0,19,0,109,111,66,111,116,116,111,109,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,255,255,1,0,16,0,109,111,69,110,100,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,0,0,0,0,0,0,0,0,0,0,0,0,0,0"
    selection1 = selection1 & ",Type=1"

    'Pie curve Edge-1
    selection2 = "68,20,0,0,3,0,0,0,255,254,255,0,0,0,0,0,255,255,1,0,11,0,109,111,69,100,103,101,82,101,102,95,99,1,0,0,0,0,0,0,0,5,0,0,0,4,3,0,0,0,0,0,0,125,195,148,37,173,73,178,84,125,195,148,37,173,73,178,84,0,0,255,255,1,0,23,0,109,111,70,114,111,109,83,107,116,69,110,116,83,117,114,102,73,100,82,101,112,95,99,0,0,255,255,1,0,6,0,109,111,70,82,95,99,255,255,1,0,13,0,109,111,69,120,116,79,98,106,101,99,116,95,99,255,255,1,0,17,0,109,111,67,83,116,114,105,110,103,72,97,110,100,108,101,95,99,255,254,255,92,75,0,58,0,92,0,97,0,112,0,105,0,92,0,72,0,69,0,76,0,80,0,92,0,83,0,97,0,109,0,112,0,108,0,101,0,32,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,83,0,105,0,109,0,117,0,108,0,97,0,116,0,105,0,111,0,110,0,92,0,50,0,48,0,49,0,50,0,92,0,65,0,117,0,116,0,111,0,84,0,101,0,115,0,116,0,70,0,105,0,108,0,101,0,115,0,92,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,115,0,92,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,46,0,83,0,76,0,68,0,"
    selection2 = selection2 & "80,0,82,0,84,0,9,128,255,254,255,13,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,2,0,0,141,213,96,79,0,0,112,0,97,0,0,0,0,0,0,0,0,0,0,0,0,0,255,254,255,7,68,0,101,0,102,0,97,0,117,0,108,0,116,0,0,0,0,0,0,0,0,0,100,0,100,0,30,0,0,0,252,214,96,79,1,0,0,0,0,0,255,255,1,0,19,0,109,111,66,111,116,116,111,109,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,255,255,1,0,16,0,109,111,84,111,112,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,255,255,1,0,16,0,109,111,69,110,100,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,0,0,0,0,0,0,0,0"
    selection2 = selection2 & ",Type=1"

    'Pie edge
    selection3 = "68,20,0,0,3,0,0,0,255,254,255,0,0,0,0,0,255,255,1,0,11,0,109,111,69,100,103,101,82,101,102,95,99,1,0,0,0,0,0,0,0,5,0,0,0,6,3,0,0,0,0,0,0,125,195,148,37,173,73,178,84,125,195,148,37,173,73,178,84,0,0,255,255,1,0,23,0,109,111,70,114,111,109,83,107,116,69,110,116,83,117,114,102,73,100,82,101,112,95,99,0,0,255,255,1,0,6,0,109,111,70,82,95,99,255,255,1,0,13,0,109,111,69,120,116,79,98,106,101,99,116,95,99,255,255,1,0,17,0,109,111,67,83,116,114,105,110,103,72,97,110,100,108,101,95,99,255,254,255,92,75,0,58,0,92,0,97,0,112,0,105,0,92,0,72,0,69,0,76,0,80,0,92,0,83,0,97,0,109,0,112,0,108,0,101,0,32,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,83,0,105,0,109,0,117,0,108,0,97,0,116,0,105,0,111,0,110,0,92,0,50,0,48,0,49,0,50,0,92,0,65,0,117,0,116,0,111,0,84,0,101,0,115,0,116,0,70,0,105,0,108,0,101,0,115,0,92,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,115,0,92,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,46,0,83,0,76,0,68,0,"
    selection3 = selection3 & "80,0,82,0,84,0,9,128,255,254,255,13,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,2,0,0,141,213,96,79,0,0,112,0,97,0,0,0,0,0,0,0,0,0,0,0,0,0,255,254,255,7,68,0,101,0,102,0,97,0,117,0,108,0,116,0,0,0,0,0,0,0,0,0,100,0,100,0,30,0,0,0,252,214,96,79,1,0,0,0,0,0,255,255,1,0,16,0,109,111,69,110,100,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,0,0,0,0,255,255,1,0,19,0,109,111,66,111,116,116,111,109,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,255,255,1,0,16,0,109,111,84,111,112,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,0,0,0,0"
    selection3 = selection3 & ",Type=1"

    'Pie edge
    selection4 = "68,20,0,0,3,0,0,0,255,254,255,0,0,0,0,0,255,255,1,0,11,0,109,111,69,100,103,101,82,101,102,95,99,1,0,0,0,0,0,0,0,5,0,0,0,4,3,0,0,0,0,0,0,125,195,148,37,173,73,178,84,125,195,148,37,173,73,178,84,0,0,255,255,1,0,23,0,109,111,70,114,111,109,83,107,116,69,110,116,83,117,114,102,73,100,82,101,112,95,99,0,0,255,255,1,0,6,0,109,111,70,82,95,99,255,255,1,0,13,0,109,111,69,120,116,79,98,106,101,99,116,95,99,255,255,1,0,17,0,109,111,67,83,116,114,105,110,103,72,97,110,100,108,101,95,99,255,254,255,92,75,0,58,0,92,0,97,0,112,0,105,0,92,0,72,0,69,0,76,0,80,0,92,0,83,0,97,0,109,0,112,0,108,0,101,0,32,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,83,0,105,0,109,0,117,0,108,0,97,0,116,0,105,0,111,0,110,0,92,0,50,0,48,0,49,0,50,0,92,0,65,0,117,0,116,0,111,0,84,0,101,0,115,0,116,0,70,0,105,0,108,0,101,0,115,0,92,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,115,0,92,0,77,0,97,0,99,0,114,0,111,0,115,0,92,0,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,46,0,83,0,76,0,68,0,"
    selection4 = selection4 & "80,0,82,0,84,0,9,128,255,254,255,13,76,0,105,0,110,0,101,0,97,0,114,0,68,0,121,0,110,0,97,0,109,0,105,0,99,0,2,0,0,141,213,96,79,0,0,112,0,97,0,0,0,0,0,0,0,0,0,0,0,0,0,255,254,255,7,68,0,101,0,102,0,97,0,117,0,108,0,116,0,0,0,0,0,0,0,0,0,100,0,100,0,30,0,0,0,252,214,96,79,1,0,0,0,0,0,255,255,1,0,16,0,109,111,84,111,112,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,255,255,1,0,16,0,109,111,69,110,100,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,0,0,0,0,255,255,1,0,19,0,109,111,66,111,116,116,111,109,69,100,103,101,73,100,82,101,112,95,99,0,0,5,128,8,0,30,0,0,0,252,214,96,79,1,0,0,0,0,0,0,0"
    selection4 = selection4 & ",Type=1"

    'Axis1
    selection5 = "68,20,0,0,1,0,0,0,255,254,255,0,0,0,0,0,21,0,0,0"
    selection5 = selection5 & ",Type=1"

        'Store constants in a collection
        PIDCollection.Add(selection1, "selection1")
        PIDCollection.Add(selection2, "selection2")
        PIDCollection.Add(selection3, "selection3")
        PIDCollection.Add(selection4, "selection4")
        PIDCollection.Add(selection5, "selection5")

        PIDInitializer = PIDCollection
    End Function

    Function ProcErrCode(ByVal errCode As Long) As String
        Select Case errCode
            Case 0
                ProcErrCode = "Successful."
            Case 1 To 21
                ProcErrCode = "Incorrect input conditions."
            Case 22
                ProcErrCode = "Authorization failed for this analysis type."
            Case 23
                ProcErrCode = "Mesh not found."
            Case 24
                ProcErrCode = "Analysis failed."
            Case Else
                ProcErrCode = "Unknown error condition."
        End Select
    End Function

  
    Public swApp As SldWorks


End Class