Hide Table of Contents

Point Light PropertyManager

A point light comes from a very small light source located at a specific coordinate in the model space. This type of light source emits light in all directions. You can modify the intensity, color, and position of the light source.

To display this PropertyManager:

In the DisplayManager, click View Scenes, Lights and Cameras . Under Lights, right-click Point and select Edit Point Light.

When the PropertyManager appears, a manipulator appears in the graphics area. To move the light in the graphics area, move the pointer over the manipulator. When the pointer changes to , you can drag the manipulator.

Basic Tab - Basic

  On in SolidWorks Switches the light off or on in the model.
  Keep light when scene changes Retains light with model after a scene change. By default, lights are replaced when a scene changes. For example, set this option when you use a point light to illuminate an occluded section of the model.
  Edit Color Displays the Color palette, so you can select colored light rather than the default white light.
Ambient Controls the intensity of the light source. Move the slider or type a value between 0 and 1. A higher value results in more light. The level changes equally on all sides of the model.
Brightness Controls the brightness of the light source. Move the slider or type a value between 0 and 1. A higher value results in more light on the side of the model closest to the source.
Specularity Controls the extent to which shiny surfaces exhibit bright highlights where the light strikes them. Move the slider or type a value between 0 and 1. A higher value results in more dramatic highlights and a shinier appearance.

Basic Tab - Light Position

Coordinate System

Spherical

Uses a spherical coordinate system to specify the position of the light source. Drag the manipulator in the graphics area or set values in the PropertyManager.

Lock to model Maintains the position of the light relative to the model. When cleared, the light remains fixed in the model space.
longitude.png Longitude

latitude.png Latitude

Distance

Sets the location of the light in the coordinate system.
Coordinate System

Cartesian

Uses a Cartesian coordinate system to specify the position of the light source. Drag the manipulator in the graphics area or set values in the PropertyManager.

Lock to model Maintains the position of the light relative to the model. When cleared, the light remains fixed in the model space.
line_start_x.pngX coordinate

line_start_y.pngY coordinate

Z coordinate

Sets the location of the light in the coordinate system.

PhotoView Tab - PhotoView Controls

The PhotoView tab is available when PhotoView is added in.

On in PhotoView Turns on the light in PhotoView. The light is off by default. Also enables PhotoView lighting options.
PhotoView brightness Sets the brightness of the light in PhotoView.

PhotoView Tab - Shadows

Shadows Enables shadows in PhotoView.
Point light radius Sets the radius of the point light in PhotoView, affecting softness of shadows. Lower values sharpen shadows. Higher values soften them but may affect rendering times.
Shadow quality Reduces graininess in softer shadows. As you increase Point light radius, experiment with higher values of this setting to reduce graininess. Increasing this setting increases render times.

PhotoView Tab - Fog

Fog Enables the fog effect in PhotoView.
Fog radius Sets the extent of fog around the light.
Fog quality Reduces graininess when Fog radius is increased. Increasing this setting increases render times.


Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Point Light PropertyManager
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:




x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: SOLIDWORKS 2014 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.