Welcome
Expand Getting StartedGetting Started
Expand SOLIDWORKS API HelpSOLIDWORKS API Help
Expand SOLIDWORKS PDM Professional API HelpSOLIDWORKS PDM Professional API Help
Expand FeatureWorks API HelpFeatureWorks API Help
Expand SOLIDWORKS Costing API HelpSOLIDWORKS Costing API Help
Expand SOLIDWORKS Document Manager API HelpSOLIDWORKS Document Manager API Help
Expand SOLIDWORKS Routing API HelpSOLIDWORKS Routing API Help
Collapse SOLIDWORKS Simulation API HelpSOLIDWORKS Simulation API Help
Expand SOLIDWORKS Sustainability API HelpSOLIDWORKS Sustainability API Help
Expand SOLIDWORKS Toolbox API HelpSOLIDWORKS Toolbox API Help
Expand SOLIDWORKS Utilities API HelpSOLIDWORKS Utilities API Help
Expand SOLIDWORKS Workgroup PDM API HelpSOLIDWORKS Workgroup PDM API Help
Expand eDrawings API HelpeDrawings API Help
Hide Table of Contents
ICWLoadsAndRestraintsManager Interface Members

The following tables list the members exposed by ICWLoadsAndRestraintsManager.

Public Properties

 NameDescription
PropertyCountGets the number of loads and restraints defined in the active study.  
Top

Public Methods

 NameDescription
MethodAddBearingLoadAdds a bearing load.  
MethodAddBoltConnectorAdds a bolt connector.  
MethodAddCentrifugalForceCreates a centrifugal force.  
MethodAddConvectionCreates a convection load for thermal studies.  
MethodAddCyclicSymmetryRestraintAdds a cyclic symmetry restraint.  
MethodAddDistributedMassCreates a distributed mass.  
MethodAddEdgeWeldConnectorCreates the specified edge weld connector.  
MethodAddElasticConnectorAdds an elastic support fixture.  
MethodAddForceObsolete. Superseded by ICWLoadsAndRestraintsManager::AddForce2.  
MethodAddForce2Obsolete. Superseded by ICWloadsAndRestraintsManager::AddForce3.  
MethodAddForce3Creates a force.  
MethodAddGravityAdds a gravity load.  
MethodAddHeatFluxCreates a heat flux load for thermal studies.  
MethodAddHeatPowerCreates a heat power load for thermal studies.  
MethodAddInitialConditionForDynamicStudyCreates the initial (time = 0) condition for displacements, velocities, or accelerations in modal time history and nonlinear dynamic studies.  
MethodAddLinkConnectorAdds a link connector.  
MethodAddPinConnectorAdds a pin connector.  
MethodAddPrescribedDisplacementApplies the specified prescribed displacement to the specified geometric entities to create a fixture.  
MethodAddPressureCreates pressure.  
MethodAddRadiationCreates a radiation load for thermal studies.  
MethodAddRemoteLoadCreates a remote load of the specified type at the specified location.  
MethodAddRestraintCreates a restraint.  
MethodAddRigidConnectorAdds a rigid connector.  
MethodAddSelectedBaseExcitationApplies a base excitation to the specified restraint along the specified directions for dynamic studies.  
MethodAddSpotWeldConnectorAdds a spot weld connector.  
MethodAddSpringConnectorAdds a spring connector.  
MethodAddTemperatureCreates a temperature load for thermal studies.  
MethodAddUniformBaseExcitationAdds a uniform base excitation to all locations restrained in the specified directions for dynamic studies.  
MethodCopyLoadsAndRestraintsToStudyCopies the specified loads and restraints to the specified study.  
MethodDeleteLoadsAndRestraintsDeletes a load or restraint.  
MethodGetEdgeWeldConnectorGets the edge weld connector at the specified index.  
MethodGetLoadsAndRestraintsGets the load or restraint at the specified index.  
Top

See Also



Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   ICWLoadsAndRestraintsManager Interface Members
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:

x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: API Help (English only) 2017 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.

0.20.24