# Document Properties - Units

Specify document-level units properties. Available for all document types.

To open this page:

With a document open, do one of the following:

- In the status bar, click Unit System, then click Edit Document Units.
- Click Options (Standard toolbar). On the Document Properties tab, select Units.

- Grid spacing
- Dimension witness line gap and bent leader length
- Dimension offset distances
- Note bent leader length
- Balloon bent leader length
- Arrow size
- Text scale and Always display text at the same size
- Material density

To save a document as a template:

- Click .
- Navigate to the location of your SOLIDWORKS templates.
The default location is C:\ProgramData\SOLIDWORKS\SOLIDWORKS

`version`\templates\. - For Save as type, select the appropriate template type for your document.
For example, for a part, select Part Templates (*.prtdot).

- Click Save.

## Unit system

Sets the document-level units and precision to a standard system or lets you modify units.

- MKS (meter, kilogram, second)
- CGS (centimeter, gram, second)
- MMGS (millimeter, gram, second)
- IPS (inch, pound, second)

Click Custom to modify units in the table.

## Basic Units

- Length
Units Decimals Fractions More Determined by your Unit system selection.

Based on selection, displays from two to eight decimal places. None displays no decimal places.

An integer for the denominator, between 2 and 256.

For inches, mils, microinches, or feet and inches, only.

Round to Nearest Fraction

Overrides decimal rounding for fraction displays.

Convert from 2'4" to 2'-4"

Displays

`feet - inches`when you import from the`feet inches`format. - Dual Dimension Length
Units Decimals Fractions More Click the list to modify. Based on selection, displays from two to eight decimal places. None displays no decimal places.

An integer for the denominator, between 2 and 256.

For inches, mils, microinches, or feet and inches, only.

Round to Nearest Fraction

Overrides decimal rounding for fraction displays.

Convert from 2'4" to 2'-4"

Displays

`feet - inches`when you import from the`feet inches`format. - Angle
Units Decimals Fractions More Click the list to modify. For degrees or radians only.

Based on selection, displays from two to eight decimal places. None displays no decimal places.

## Mass/Section Properties

Displays the document-level length, mass, and density properties that appear in the Mass Properties or Section Properties PropertyManager as determined by your Unit system selection. In addition, these properties specify units used in SimulationXpress.

To modify units, from Unit system, select Custom.

Type | Units | Decimals |
---|---|---|

Length | The length units used for volume, surface area, center of mass, and other mass or section properties that depend on length. For example, for Length in inches, surface area units are in square inches. | Based on selection, displays from two to eight decimal places. None displays no decimal places. |

Mass | The mass units used for density and other mass or section properties that depend on mass. | |

Per Unit Volume | The volume units used for density. For example, for Mass in grams and Per Unit Volume in cubic centimeters, density units are in grams per cubic centimeter. |

## Motion Units (Assemblies Only)

Displays document-level units for time, force, power, and energy for motion study results and features as determined by your Unit system selection.

## Decimal rounding

Provides control over decimal rounding in dimensions.

Round half away from zero |
Rounding method where 5 rounds the previous digit up. For example, 46.15 at one decimal place becomes 46.2. |

Round half towards zero |
Rounding method where 5 keeps the previous digit unchanged. For example, 46.15 at one decimal place becomes 46.1. |

Round half to even |
Rounding method where 5 is the removed digit. When the previous digit is even, the digit remains unchanged. For example, 46.25 at one decimal place becomes 46.2. When the previous digit is odd, the digit is rounded up to the next even number. This method is also referred to as Statistician's Rounding. For example, 46.15 at one decimal place becomes 46.2. |

Truncate without rounding |
Method that removes digits without rounding. For example, 46.19 at one decimal place becomes 46.1. |

Only apply rounding method to dimensions |
(Parts and Assemblies only). When selected, this option applies the rounding rule to dimensions and their tolerances, including dimensions whose values are derived from equations. When cleared, this option applies the rounding rule to any numeric display where rounding occurs, including dialog boxes, such as Mass Properties. |

**Parent topic**Document Properties