Hide Table of Contents

Specifying Units and Precision

The UnitSystem command lets you set:

  • Formats for linear and angular units
  • Accuracy levels by specifying the number of decimal places
  • The reference unit of measurement for Blocks and drawings in the drawing

You can set the linear and angular unit formats and precision independently.

The unit settings are saved with each drawing, and so they can be different for each drawing.

To specify units and precision:

  1. Click Format > Unit System (or type UnitSystem).

    In the Options dialog box, the Drawing Settings page opens and Unit System expands.

  2. Under Base angle:
    • Set the base angle that specifies a direction for 0°. For example, surveyors normally set 0° as "up" on the page. This setting ensures the correct display of angle and distance for drawing lines; the display on the status bar updates according to the angle zero direction and the orientation.
    • Select Clockwise to increase angles in a clockwise direction.
    • Set the rotation angle, or click Select in graphics area  to set the rotation angle and second point in the graphics area.
  3. Under Length, set the:
    • Type of linear units.
    • Precision from 0 to 8 decimal places.

    The selected units are displayed in the Preview area.

    Examples of linear units:

    Unit Type Example 1 Example 2
    Architectural (Feet and Inches) 0'-1 1/2" 125'-0"
    Decimal 1.5000 1500.0000
    Engineering (Feet and Inches) 0'-1.5000" 125'-0.0000"
    Fractional 1 1/2 1500
    Scientific (Scientific exponential notation) 1.5000E+00 1.5000E+03
  4. Under Angle, set the:
    • Type of angular units.
    • Precision from 0 to 8 decimal places.

    The selected units are displayed in the Preview area.

    Examples of angular units:

    Unit Type Example 1 Example 2
    Decimal Degrees (Metric Units) 12.500 180
    Degrees / Minutes / Seconds 12d30'0" 180d0'0"
    Grads (400 grads equal to 360°) 13.889g 200.000g
    Radians (2 pi radians equal to 360°) 0.218r 3.142r
    Surveyor's Unit System (Compass bearings; N,S,E,W with deflection from North and South) N 77d30'0" E W
  5. Under Units scale, in Block units format, select the reference unit of measurement for Blocks and drawings in the drawing. Select Unitless to prevent scaling of entities. If the units of a Block (or drawing) to be inserted differ from the units in Block units format, the Block is scaled. This insertion scale determines the ratio between the units in the source and the units in the target drawing.
  6. Click OK.

Access

Command: UnitSystem

Menu: Format > Unit System



Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Specifying Units and Precision
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:




x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: 2022 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.