3DS

> Simulation Tutorials for SOLIDWORKS Connected Users > Static Tutorials (SOLIDWORKS Standard and above) > Spot Weld of Automobile Parts > Opening the Assembly

Compass

Collapse Simulation Tutorials for SOLIDWORKS Connected Users

Simulation Tutorials for SOLIDWORKS Connected Users

Collapse Static Tutorials (SOLIDWORKS Standard and above)

Static Tutorials (SOLIDWORKS Standard and above)

Expand Static (Stress) Analysis of a Part

Static (Stress) Analysis of a Part

Expand Static Analysis of an Assembly

Static Analysis of an Assembly

Expand Static Analysis with a Mixed Mesh

Static Analysis with a Mixed Mesh

Expand Analysis of a Fuel Storage Tank

Analysis of a Fuel Storage Tank

Expand Contact Analysis of an Eyebar Assembly

Contact Analysis of an Eyebar Assembly

Expand Large Displacement Contact

Large Displacement Contact

Expand Shrink Fitting of Two Rings

Shrink Fitting of Two Rings

Expand Remote Forces

Expand Static Analysis of a Sheet Metal Part

Static Analysis of a Sheet Metal Part

Expand Converting Solid Geometry to Surfaces

Converting Solid Geometry to Surfaces

Expand Converting a Thin Solid Body into a Sheet Metal and Surface Body

Converting a Thin Solid Body into a Sheet Metal and Surface Body

Expand Failure Analysis of a Composite Joint (Simulation Premium only)

Failure Analysis of a Composite Joint (Simulation Premium only)

Expand Symmetry Restraints for Solid and Shell Models

Symmetry Restraints for Solid and Shell Models

Expand Using Adaptive Methods

Using Adaptive Methods

Expand Analysis of a Pulley Under a Bearing Force

Analysis of a Pulley Under a Bearing Force

Expand Pliers Defined Using Pins

Pliers Defined Using Pins

Expand Analysis of a Basketball Assembly With Bolts

Analysis of a Basketball Assembly With Bolts

Collapse Spot Weld of Automobile Parts

Spot Weld of Automobile Parts

Opening the Assembly

Defining Spot Welds

Meshing the Model and Running the Study

Viewing the Analysis Results

Expand Design Check for Connectors

Design Check for Connectors

Expand Design Check for a Mixed Mesh Assembly

Design Check for a Mixed Mesh Assembly

Expand Static Analysis of a Truss

Static Analysis of a Truss

Expand Creating Beam Diagrams

Creating Beam Diagrams

Expand Actuator Mechanism with Connectors

Actuator Mechanism with Connectors

Expand Frequency Tutorial (Simulation Professional and above)

Frequency Tutorial (Simulation Professional and above)

Expand Design Insight Tutorials (Simulation Professional and above)

Design Insight Tutorials (Simulation Professional and above)

Expand Thermal Tutorials (Simulation Professional and above)

Thermal Tutorials (Simulation Professional and above)

Expand Buckling Tutorial (Simulation Professional and above)

Buckling Tutorial (Simulation Professional and above)

Expand Fatigue Tutorials (Simulation Standard and above)

Fatigue Tutorials (Simulation Standard and above)

Expand Nonlinear Tutorials (Simulation Premium only)

Nonlinear Tutorials (Simulation Premium only)

Expand Linear Dynamics Tutorials (Simulation Premium only)

Linear Dynamics Tutorials (Simulation Premium only)

Expand Drop Test Tutorials (Simulation Professional and above)

Drop Test Tutorials (Simulation Professional and above)

Expand Pressure Vessel Design Tutorial (Simulation Professional and above)

Pressure Vessel Design Tutorial (Simulation Professional and above)

Expand Trend Tracker Tutorial (Simulation Standard and above)

Trend Tracker Tutorial (Simulation Standard and above)

Expand Motion Tutorials (available with SOLIDWORKS Motion)

Motion Tutorials (available with SOLIDWORKS Motion)

Expand Simulation Validation for SOLIDWORKS Connected Users

Simulation Validation for SOLIDWORKS Connected Users

Hide Table of Contents

Opening the Assembly

Browse to drive letter:\Users\Public\Public Documents\SOLIDWORKS\SOLIDWORKS version\samples\Simulation Examples\Car_Model.SLDASM and open the file.

The Partial study includes:

A static study with shell mesh
Cast stainless steel for all components
A Fixed restraint on the bottom edges of the two side shells
A force of 250 lbf on the roof of the car
No Penetration contact sets between the roof and each of the two sides

Search 'Opening the Assembly' in the SOLIDWORKS Knowledge Base.

Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required


*Email:
Subject:		Feedback on Help Topics
Page:		Opening the Assembly
*Comment:
*		I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Cancel

Print Topic

Select the scope of content to print:

This topic and all topics linked from this topic

Just this topic

This topic and only immediate topics under it

This selected topic and all subtopics

Cancel

x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

Never show this message again

x

Web Help Content Version: SOLIDWORKS Simulation Tutorials (3DEXPERIENCE SOLIDWORKS) 2025 SP1

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.