Hide Table of Contents

Sustainability Task Pane - Main

When you have an assembly open with all component materials specified or excluded, the Task Pane opens to the Assembly Process to let you specifiy parameters such as the amount of energy required to assemble the product.

To display the Task Pane, open an assembly and then do one of the following:

  • Click Sustainability (Tools toolbar or Evaluate CommandManager tab).
  • Click Tools > Sustainability.

Typically, the main Sustainability Task Pane opens. When you analyze an assembly for which a component has an unassigned or unsupported material, a Sustainability Task Pane containing the Task List opens.

Assembly Process

Sets the region of manufacture, for example, Asia.

Click the map to set the region.
Available regions are North America, Europe, Asia, Japan, South America, Australia, and India. Data is not available for all regions. Regions that contain data are highlighted when you hover over them.
Built to last Length of time the part will last.

The numeric field and increments are editable.

Energy required for assembly process Sets the Fuel type (Electricity or Natural Gas) and Amount required to manufacture the assembly.


Region Sets the region where the product is transported and used, for example, Asia.PM_Regions_Asia_Sustain.gif

Select a region from the drop-down list or click a region in the map to set the region.

Energy Needs over lifespan Specifies the Type of energy and Amount of energy that is used over the products's lifespan.

Energy choices are:

  • Electricity
  • Natural Gas
  • Diesel
  • Gasoline
  • Kerosene
  • Light Fuel Oil


Shows the default mode of transportation and distance traveled from the Manufacturing region to the Use region.

sustainability_train.gif Train   sustainability_boat.gif Boat
sustainability_truck.gif Truck   sustainability_plane.gif Plane

To edit these values, click a transportation mode's button and type in the field that is enabled. When you add values for a transportation mode or modify the default mode, the field turns yellow and a Reset to Defaults button appears to let you discard your changes.

End of Life

Shows default percentages based on the value of the materials in the sustainability database. The values of all the components in the assembly are rolled up by weight.

tool_end_of_life_recycle.gif Recycled
tool_end_of_life_incinerate.gif Incinerated
tool_end_of_life_landfill.gif Landfill

The total of the values always equals 100%. If you change the recycled or incinerated value, the landfill value updates. If you change the landfill value, the recycled value changes.

When you edit a value, the field turns yellow and a Reset to Defaults button appears to let you discard your changes.

Environmental Impact

The Environmental Impact dashboard provides real-time feedback about the environmental impact of the design. SolidWorks Sustainability products let you select either the CML or TRACI environmental impact assessment methodology to calculate the environmental indicators (carbon footprint, energy consumption, water eutrophication, and air acidification).

  Impact Parameters Sustain_EI_Header_OH_HIDD.gif
Display the impact for each parameter on the environment impact areas.
Use is only calculated for assemblies.
  Duration of Use Length of time the product will be used.

This number is used in conjunction with the Built to Last value in the Manufacturing section to calculate more accurate results.

In SustainabilityXpress, this value defaults to 1 year.

In full Sustainability, the numeric field and increments are editable.

  Environmental Impact Areas

Carbon Footprint

A measure of carbon dioxide and equivalents, such as carbon monoxide and methane, that are released into the atmosphere primarily by burning fossil fuels.

Energy Consumption

All forms of nonrenewable energy consumed over the entire life cycle of the product.

Air Acidification

Acidic emissions, such as sulfur dioxide and nitrous oxides, which eventually lead to acid rain.

Water Eutrophication

Contamination of water ecosystems by waste water and fertilizers, resulting in algae blooms and the eventual death of plant and animal life.

Pie charts show the percentage of impact of each parameter on the four environmental impact areas.

Bars below each pie chart compare the effect of the current impact paramaters to the effect of previous or baseline parameters.

Green bars indicate the current parameters have a lower environmental impact than the previous parameters.

Red bars indicate the current parameters have a higher environmental impact than the previous parameters.

Mouse over the bars to see the current and baseline values.

Arrows beside the pie charts emphasize the increase sustainability_up_arrow_percent or decrease sustainability_down_arrow_percent in environmental impact and the percentage of change.

  Material Financial Impact

Bars compare the financial impact of the Current and Previous materials you have selected.

A green bar indicates that the current material has a lower financial impact. A red bar indicates a higher financial impact.

Mouse over the bars to see the current and previous values.

An arrow beside the bars indicates the percentage of change.

tool_sustainability_home.gif Home Returns you to the initial display of the Environmental Impact Dashboard.
  Calculation method Calculation method used for environmental impact results.


CML (default) is based on European regional conditions.

For Life Cycle Assessment (LCA) studies outside of North America, the CML methodology is the most commonly-used set of environmental indicators used for LCA.


TRACI is based on regional conditions of the United States and can be used to accurately model North American LCA studies.

Save As Opens the Sustainability Output dialog box, where you can choose to generate a:
  • Report

    Generates a Sustainability report in .docx format.

  • Spreadsheet

    Generates a spreadsheet of results and inputs in .csv format.

  • GaBi input file

    Generates a file in .xml format that can be read into GaBi LCA software.

Set Baseline Sets the current selections in the Task Pane as the baseline against which you compare different selections. The Baseline bar is the bottom bar below the pie charts.
Import Baseline Lets you import an existing baseline to use in the current model.
Online Info Opens a Web site that provides additional information about Sustainability, including a calculator to help you understand the impact of your design.

Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

Subject:   Feedback on Help Topics
Page:   Sustainability Task Pane - Main
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:


We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again

Web Help Content Version: SOLIDWORKS 2014 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.