Hide Table of Contents

Constructing InfiniteLines

InfiniteLines are a set of one or more construction lines that extend indefinitely in both directions from an origin.

Use InfiniteLines to create frameworks or grids for use in drawing construction.

To construct one or more InfiniteLines:

  1. Click Draw > InfiniteLine (or type InfiniteLine).
  2. In the graphics area, specify the:
    1. Central position of the InfiniteLine.
    2. Through point to define the first InfiniteLine direction.
    3. Different through points to define other InfiniteLines through the same origin, or press Enter.

   Draw InfiniteLines on separate Layers that you can turn off or freeze prior to printing. Alternatively, delete InfiniteLines when the drawing is complete.

To create horizontal InfiniteLines:

  1. Click Draw > InfiniteLine (or type InfiniteLine).
  2. Specify the Horizontal option.
  3. In the graphics area, specify:
    1. A point to define the line position.
    2. Other points to define parallel horizontal lines, or press Enter.

To create vertical InfiniteLines:

  1. Click Draw > InfiniteLine (or type InfiniteLine).
  2. Specify the Vertical option.
  3. In the graphics area, specify:
    1. A point to define the line position.
    2. Other points to define parallel vertical lines, or press Enter.

To create parallel InfiniteLines at an angle from the origin:

  1. Click Draw > InfiniteLine (or type InfiniteLine).
  2. Specify the Angle option.
  3. Type an angle value in the specified angle drawing units or specify the Reference option to specify a reference entity, and then enter the angle from the reference entity.

    The InfiniteLine appears at the specified angle to the horizontal or to the specified entity.

  4. In the graphics area, specify:
    1. A point to define the line position.
    2. Other points to define parallel lines, or press Enter.

To create bisecting InfiniteLines from a vertex:

  1. Click Draw > InfiniteLine (or type InfiniteLine).
  2. Specify the Angle Bisect option.
  3. In the graphics area, specify:
    1. A point to define the vertex position.
    2. A point to define the first angle for the bisecting InfiniteLine.
    3. A point to define the second angle that determines the bisecting InfiniteLine through the vertex.
    4. Other points to define other bisecting InfiniteLines, or press Enter.

To create InfiniteLines that are offset from other linear entities:

  1. Click Draw > InfiniteLine (or type InfiniteLine).
  2. Specify the Offset option.
  3. Type an offset distance.
  4. In the graphics area:
    1. Select a linear source entity.
    2. Specify the location of the InfiniteLine.
  5. Repeat step 4 or press Enter.

  Instead of performing steps 3 and 4, you can specify the Specify Position option, select a linear source entity, and click a point in the graphics area to define the offset distance.

Access

Command: InfiniteLine

Menu: Draw > InfiniteLine



Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Constructing InfiniteLines
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:




x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: 2020 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.