3DS

> Simulation Tutorials for SOLIDWORKS Connected Users > Nonlinear Tutorials (Simulation Premium only) > Nonlinear Contact Analysis of an O-Ring > Restraining the Model in the Radial Direction

Compass

Collapse Simulation Tutorials for SOLIDWORKS Connected Users

Simulation Tutorials for SOLIDWORKS Connected Users

Expand Static Tutorials (SOLIDWORKS Standard and above)

Static Tutorials (SOLIDWORKS Standard and above)

Expand Frequency Tutorial (Simulation Professional and above)

Frequency Tutorial (Simulation Professional and above)

Expand Design Insight Tutorials (Simulation Professional and above)

Design Insight Tutorials (Simulation Professional and above)

Expand Thermal Tutorials (Simulation Professional and above)

Thermal Tutorials (Simulation Professional and above)

Expand Buckling Tutorial (Simulation Professional and above)

Buckling Tutorial (Simulation Professional and above)

Expand Fatigue Tutorials (Simulation Standard and above)

Fatigue Tutorials (Simulation Standard and above)

Collapse Nonlinear Tutorials (Simulation Premium only)

Nonlinear Tutorials (Simulation Premium only)

Expand Geometrically Nonlinear Analysis of a Plate

Geometrically Nonlinear Analysis of a Plate

Expand Rolling a Sheet into a Ring

Rolling a Sheet into a Ring

Expand Elasto-Plastic Analysis of a C-Clamp

Elasto-Plastic Analysis of a C-Clamp

Expand Snap-Through/Snap-Back of a Cylindrical Sheet

Snap-Through/Snap-Back of a Cylindrical Sheet

Expand Nonlinear Contact Analysis of a Pipe Holder

Nonlinear Contact Analysis of a Pipe Holder

Collapse Nonlinear Contact Analysis of an O-Ring

Nonlinear Contact Analysis of an O-Ring

Opening the Model and Defining a Nonlinear Study

Assigning Material Properties

Applying Symmetry Restraints

Restraining the Model in the Radial Direction

Restraining the Bottom Face of the Model

Applying Prescribed Displacement

Defining Contact Between Model Faces

Defining Contact Between the Top Plate and the Groove

Meshing the Model and Running the Analysis

Viewing Results

Animating the Displacement Plot and Plotting von Mises Stresses

Expand Snapping of a Clip Assembly

Snapping of a Clip Assembly

Expand Simulation of Orthodontic Archwire with Nitinol Material Model

Simulation of Orthodontic Archwire with Nitinol Material Model

Expand 2D Simplification Study of a 3D Model

2D Simplification Study of a 3D Model

Expand Linear Dynamics Tutorials (Simulation Premium only)

Linear Dynamics Tutorials (Simulation Premium only)

Expand Drop Test Tutorials (Simulation Professional and above)

Drop Test Tutorials (Simulation Professional and above)

Expand Pressure Vessel Design Tutorial (Simulation Professional and above)

Pressure Vessel Design Tutorial (Simulation Professional and above)

Expand Trend Tracker Tutorial (Simulation Standard and above)

Trend Tracker Tutorial (Simulation Standard and above)

Expand Motion Tutorials (available with SOLIDWORKS Motion)

Motion Tutorials (available with SOLIDWORKS Motion)

Expand Simulation Validation for SOLIDWORKS Connected Users

Simulation Validation for SOLIDWORKS Connected Users

Hide Table of Contents

Restraining the Model in the Radial Direction

The outer faces of the chamber are restrained in the radial direction.

In the Simulation study tree, right-click the Fixtures icon and select Advanced Fixtures.
In the PropertyManager, do the following:
1. Under Advanced (Use Reference Geometry), select On Cylindrical Faces.
2. In the graphics area, click the cylindrical face of the groove as shown in the figure.
3. Under Translations, click Radial and make sure that 0 appears in the value box.
4. Click .

Search 'Restraining the Model in the Radial Direction' in the SOLIDWORKS Knowledge Base.

Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required


*Email:
Subject:		Feedback on Help Topics
Page:		Restraining the Model in the Radial Direction
*Comment:
*		I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Cancel

Print Topic

Select the scope of content to print:

This topic and all topics linked from this topic

Just this topic

This topic and only immediate topics under it

This selected topic and all subtopics

Cancel

x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

Never show this message again

x

Web Help Content Version: SOLIDWORKS Simulation Tutorials (3DEXPERIENCE SOLIDWORKS) 2025 SP2

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.