• About
  • Learning Resources
  • My.SolidWorks
  • Subscription Services
3DS
> Getting Started > Introduction to SOLIDWORKS > Adding the Tall Cylinder Hole
Compass
SOLIDWORKS Connected Tutorials
 |  Print     | Feedback on this topic  
SOLIDWORKS Connected Tutorials
Sample Files
Expand SOLIDWORKS Connected and the 3DEXPERIENCE PlatformSOLIDWORKS Connected and the 3DEXPERIENCE Platform
Expand OrientationOrientation
Collapse Getting StartedGetting Started
Collapse Introduction to SOLIDWORKSIntroduction to SOLIDWORKS
Before You Begin
Opening SOLIDWORKS Connected for the First Time
Specifying Units of Measurement
My First Part
Sketching the Circle
Adding Dimensions
Extruding the Base Feature
Saving the Part
Sketching the Boss
Dimensioning the Boss Sketch
Offsetting Entities
Extruding the Ring Boss
Sketching the Hole
Dimensioning the Hole Sketch
Creating a Hole
Creating Holes Using the Hole Wizard
Modifying and Dimensioning Hole Wizard Holes
Adding Fillets
Sketching the Tall Cylinder Extrusion
Completing the Tall Cylinder Extrusion
Dimensioning the Tall Cylinder Sketch
Adding the Tall Cylinder Extrusion
Sketching the Tall Cylinder Hole
Dimensioning the Tall Cylinder Hole Sketch
Adding the Tall Cylinder Hole
Adding Fillets to the Tall Cylinder
Creating a Circular Pattern
Adding the Last Fillet
My First Drawing
Creating a New Drawing
Creating a Section View
Creating a Detail View
Creating an Isometric View
Adding Center Marks
Adding Centerlines
Placing Dimensions
Placing Detail Dimensions
Modifying the Text of Dimensions
Expand Lesson 1 - PartsLesson 1 - Parts
Expand Lesson 2 - AssembliesLesson 2 - Assemblies
Expand Lesson 3 - DrawingsLesson 3 - Drawings
Expand Basic TechniquesBasic Techniques
Expand Advanced TechniquesAdvanced Techniques
Expand Productivity ToolsProductivity Tools
Expand Design EvaluationDesign Evaluation
Hide Table of Contents Show Table of Contents

Adding the Tall Cylinder Hole

Create a hole in the tall cylinder that cuts through the entire part.

  1. Click Exit Sketch on the Sketch tab.
  2. In the PropertyManager, under Direction 1, select Through All for End Condition.

  3. Click .
Parent topicIntroduction to SOLIDWORKS
Previous topic Dimensioning the Tall Cylinder Hole Sketch
Next topic Adding Fillets to the Tall Cylinder
Search 'Adding the Tall Cylinder Hole' in the SOLIDWORKS Knowledge Base.


Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Adding the Tall Cylinder Hole
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes
Cancel

Thank you for your comments. We will contact you if we have questions regarding your feedback.

Sincerely,
The SOLIDWORKS Documentation Team

Print Topic

Select the scope of content to print:

Cancel
x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: SOLIDWORKS Connected Tutorials (3DEXPERIENCE SOLIDWORKS) 2025 SP2

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.

0.20.46

Terms of Use  | Privacy Policy  | Personalize Cookie Choices  | Get a Product Demo  | Contact Sales  | Get a Quote  © 1995-2025 Dassault Systèmes. All rights reserved.