Specify document-level units properties. Available for all document types.
To open this page, with a document open, do one of the following:
- In the status bar, click Unit System, then click Edit Document Units.
- Click
Options
(Standard toolbar). On the Document Properties tab, select Units.
If you use small units such as angstroms, nanometers, microns, mils, or microinches, it is helpful to create templates as the basis for documents that use the units. The templates could include settings such as:
- Grid spacing
- Dimension witness line gap and bent leader length
- Dimension offset distances
- Note bent leader length
- Balloon bent leader length
- Arrow size
- Text scale and Always display text at the same size
- Material density
Unit system
Sets the document-level units and precision to a standard system or lets you modify units.
Standard systems are:
- MKS (meter, kilogram, second)
- CGS (centimeter, gram, second)
- MMGS (millimeter, gram, second)
- IPS (inch, pound, second)
Click Custom to modify units in the table.
You can change the unit system without opening Document Properties - Units. In the status bar, click Unit System, then click a unit system.
Basic Units
Displays document-level dimension units.
- Length
| Units |
Decimals |
Fractions |
More |
|---|
Determined by your Unit system selection.
|
Based on selection, displays from two to eight decimal places. None displays no decimal places.
|
An integer for the denominator, between 2 and 256.
For inches, mils, microinches, or feet and inches, only.
|
|
Round to Nearest Fraction
|
Overrides decimal rounding for fraction displays.
|
|
Convert from 2'4" to 2'-4"
|
Displays feet - inches when you import from the feet inches format.
|
|
- Dual Dimension Length
| Units |
Decimals |
Fractions |
More |
|---|
| Click the list to modify. |
Based on selection, displays from two to eight decimal places. None displays no decimal places.
|
An integer for the denominator, between 2 and 256.
For inches, mils, microinches, or feet and inches, only.
|
|
Round to Nearest Fraction
|
Overrides decimal rounding for fraction displays.
|
|
Convert from 2'4" to 2'-4"
|
Displays feet - inches when you import from the feet inches format.
|
|
- Angle
| Units |
Decimals |
Fractions |
More |
|---|
| Click the list to modify. |
For degrees or radians only.
Based on selection, displays from two to eight decimal places. None displays no decimal places.
|
|
|
Basic Unit Examples
| Decimal inches
|
 |
| Fractional inches |
 |
| Convert from 2'4" to 2'-4" |
 |
| Dual Dimension Length |
 |
| Degrees Minutes Seconds |
 |
| Radians |
 |
Mass/Section Properties
Displays the document-level length, mass, and density properties that appear in the Mass Properties or Section Properties PropertyManager as determined by your Unit system selection. In addition, these properties specify units used in SimulationXpress.
To modify units, from Unit system, select Custom.
| Type |
Units |
Decimals |
|---|
| Length |
The length units used for volume, surface area, center of mass, and other mass or section properties that depend on length. For example, for Length in inches, surface area units are in square inches. |
Based on selection, displays from two to eight decimal places. None displays no decimal places.
|
| Mass |
The mass units used for density and other mass or section properties that depend on mass. |
| Per Unit Volume |
The volume units used for density. For example, for Mass in grams and Per Unit Volume in cubic centimeters, density units are in grams per cubic centimeter.
|
Motion Units (Assemblies Only)
Displays document-level units for time, force, power, and energy for motion study results and features as determined by your Unit system selection.
| Decimals |
Based on selection, displays from two to eight decimal places. None displays no decimal places.
|