Hide Table of Contents

Constant Size Fillets

Creates fillets that have a constant size for the entire length of the fillet.

Items to Fillet

Edges, Faces, Features and Loops Select entities to fillet in the graphics area.
  Tangent propagation Extends the fillet to all faces that are tangent to the selected face. Example: Tangent Propagation
  Full preview Displays a fillet preview of all edges.
  Partial preview Displays a fillet preview of one edge only. Press the A key to view each fillet preview in turn.
  No preview Improves rebuild time with complex models.

Fillet Parameters

Radius Sets the fillet radius.
  Multiple radius fillet Creates fillets with different radius values for edges. You can create corners using three edges with different radii.
You cannot assign multiple radii to faces or loops with common edges.
   

Dimensions for multiple radius fillets applied to original cube-shaped body.
   

Multiple radius fillets applied.
  Profile Sets the profile type to fillet. The profile defines the cross sectional shape of the fillet.

Circular

Conic Rho pm_rho.gif

Sets the ratio that defines the weight of the curve. Enter a value between 0 and 1.

Conic Radius

Sets the radius of curvature at the shoulder point along the curve.

Setback Parameters

These options create a smooth transition between the blended surface, along the edge of the part, into the fillet corner. You select a vertex and a radius, and then assign the same or different setback distances for each edge. The setback distance is the point along each edge at which the fillet starts to blend into the three faces that meet at the common vertex. Example: Setback Fillet Preview
Before setting the Setback Parameters, under Items To Fillet:
  1. Select Multiple radius fillet.
  2. In the graphics area, select three or more edges with a common vertex for Edges, Faces, Features and Loops . You must select all the edges that meet at the common vertex.
Distance Sets the fillet setback distance measured from the vertex.
Setback Vertices Select one or more vertices in the graphics area. The setback fillet edges meet at the selected vertices.
Setback Distances Lists the edge numbers with corresponding setback Distance values. To apply a different setback distance to edges, select an edge in Setback Distances . Then set a Distance and press Enter.
  Set Unassigned Applies the current Distance to all edges that do not have assigned distances under Setback Distances .
  Set All Applies the current Distance to all edges under Setback Distances .

Fillet Options

Select through faces Enables selection of edges through faces that hide edges.
Keep Features Keeps cut or boss features visible if you apply a fillet radius large enough to cover them. Clear Keep Features to cover the cut or boss features with the fillet.

Model with no fillets

Model with Keep features applied to fillets for front boss and right cut features.

Note the front left cut and all rear bosses are not visible because Keep features was not selected for those features.

Model with Keep features applied to all fillets
Round corners Creates constant size fillets with rounded corners. You must select at least two adjacent edges to fillet. Round corner fillets have a smooth transition between edges that eliminates the sharp juncture where the edges meet.

Constant size fillets applied without Round corners

Constant size fillets applied with Round corners
Overflow type Controls the way fillets on single closed edges (circles, splines, ellipses for example) act when they meet edges. Example: Overflow Type. Select one of the following:

Default

The application selects the Keep edge or Keep surface option.

Keep edge

The model edge remains unchanged, while the fillet adjusts.

Keep surface

The fillet edge adjusts to be continuous and smooth, while the model edge changes to match the fillet edge.
Feature attachment Controls attachment of edges between intersecting features. You must select the feature in the FeatureManager design tree to display this option. Optionally select the following:

Omit attach edges

(Available when you select a feature, then click the Fillet tool.) Does not fillet the edges where the features intersect. Clear this option to fillet the intersecting edges.

Omit attach edges selected. The edge attaching the two extrude features is not filleted, but the other edges of the selected extrude feature on top are filleted.

Omit attach edges cleared. All edges of the selected extrude feature on top are filleted, including the edge attaching the two extrude features.

Contents



Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Constant Size Fillets
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:
x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: SOLIDWORKS 2014 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.

0.20.23