Hide Table of Contents

Face Fillets

Blends non-adjacent, non-continuous faces.

Face Set 1 and Face Set 2 selected Face fillet applied

Items To Fillet

Face Set 1 Select the first face or set of faces in the graphics area to blend.
Face Set 2 Select the faces in the graphics area to blend with Face Set 1.
If you select more than one face for either Face Set 1 or Face Set 2, each set of faces must be smoothly connected for the face fillet to properly propagate to all faces.
  Tangent propagation Extends the fillet to all faces that are tangent to the selected face. Example: Tangent Propagation
  Full preview Displays a fillet preview of all edges.
  Partial preview Displays a fillet preview of one edge only. Press the A key to view each fillet preview in turn.
  No Preview Improves rebuild time with complex models.

Fillet Parameters

Radial Defines the fillet by the radius.

Radius

Sets the fillet radius.
Chord Width Defines the fillet by the chord width.

Chord Width

Sets the chord width.

Face fillet defined by radius

Face fillet defined by chord width
Profile Sets the profile type to fillet. The profile defines the cross sectional shape of the fillet.

Circular

Conic Rho pm_rho.gif

Sets the ratio that defines the weight of the curve. Enter a value between 0 and 1.

Conic Radius

Sets the radius of curvature at the shoulder point along the curve.

Curvature continuous

Resolves discontinuity problems and creates a smoother curvature between adjacent surfaces. To verify the effect of the curvature continuity, you can display Zebra Stripes. You can also analyze the curvature using the curvature tool.

Curvature continuous fillets differ from standard fillets. They have a spline cross section as opposed to a circular cross section. Curvature continuous fillets are smoother than standard fillets because there is no jump in curvature at the boundary. Standard fillets include a jump at the boundary because they are tangent continuous at the boundary.

Fillet Options

Select through faces Enables selection of edges through faces that hide edges.
Hold line (Radial fillets only) Select an edge on the part or a projected split line on a face as a boundary that determines the face fillet shape. The radius of the fillet is driven by the distance between the hold line and the edge to fillet.

Faces to fillet

Hold lines

Face fillet applied

Projected split line as hold line

Face fillet applied
Help point Resolves an ambiguous selection when it may not be clear where the face blend should occur. Click in Help Point Vertex, then click a vertex on the side where you want the face fillet. A fillet is created at the location closer to the Help point.
Trim Surfaces (Surfaces only) Select one of the following:

Trim and attach

Trims the filleted faces and knits the surfaces into one surface body.

Don't trim or attach

Adds a new fillet surface, but does not trim the faces or knit the surfaces.

Contents



Provide feedback on this topic

SOLIDWORKS welcomes your feedback concerning the presentation, accuracy, and thoroughness of the documentation. Use the form below to send your comments and suggestions about this topic directly to our documentation team. The documentation team cannot answer technical support questions. Click here for information about technical support.

* Required

 
*Email:  
Subject:   Feedback on Help Topics
Page:   Face Fillets
*Comment:  
*   I acknowledge I have read and I hereby accept the privacy policy under which my Personal Data will be used by Dassault Systèmes

Print Topic

Select the scope of content to print:
x

We have detected you are using a browser version older than Internet Explorer 7. For optimized display, we suggest upgrading your browser to Internet Explorer 7 or newer.

 Never show this message again
x

Web Help Content Version: SOLIDWORKS 2014 SP05

To disable Web help from within SOLIDWORKS and use local help instead, click Help > Use SOLIDWORKS Web Help.

To report problems encountered with the Web help interface and search, contact your local support representative. To provide feedback on individual help topics, use the “Feedback on this topic” link on the individual topic page.

0.20.61